1. Manuales
  2. Marcas
  3. Sharp Manuales
  4. Proyectores
  5. PG-A10X
  6. Manual de instrucciones

Rs-232C Specifications And Command Settings - Sharp PG-A10X Manual De Instrucciones

Ocultar thumbs Ver también para PG-A10X:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 87

RS-232C Specifications and Command Settings

PC control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,
sold separately) to the projector. (See page 20 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Baud rate: 9,600 bps
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After
the projector processes the command from the computer, it sends a response code to the computer.
Command format
C1 C2 C3 C4 P1 P2 P3 P4
Response code format
Normal response
O
K
Info
• When more than one code is being sent, send each command only after the response code for the previous
command from the projector is verified.
Commands
Example: When turning on the projector, make the following setting.
Computer
P
O
W
R
CONTROL CONTENTS
Power Off (Standby)
Power On
INPUT1
INPUT2
INPUT3
Lamp Usage Time (hour)
Remaining Lamp Life (Percentage)
Lamp Status
Unit Status
Model Name Check
AV Mute Off
AV Mute On
Auto Sync Start
Note
• If an underbar (_) appears in the parameter column, enter a space. If an asterisk (*) appears, enter a
value in the range indicated in brackets under CONTROL CONTENTS.
A10X_A10S#E_Print#p51_62.p65
Command 4-digit
Parameter 4-digit
0DH
Return code (
)
_
_
_
1
COMMAND PARAMETER
P
O
W
R
_
_
_
0
OK or ERR
P
O
W
R
_
_
_
1
OK or ERR
I
R
G
B
_
_
_
1
OK or ERR
I
V
E
D
_
_
_
1
OK or ERR
I
V
E
D
_
_
_
2
OK or ERR
T
L
T
T
_
_
_
1
0~9999
T
L
T
L
_
_
_
1
0~100
T
L
P
S
_
_
_
1
0:Off, 1:On, 2:Retry, 3:Waiting, 4:Lamp Error
T
A
B
N
_
_
_
1
0:Normal, 1:Temp High, 2:Fan Err,
4:Filter Cover Err, 8:Lamp 100 hours,
16:Lamp Burnt-out, 32:Lamp Not Lit,
64:Temp Abnormally High
T
N
A
M
_
_
_
1
PROJECTOR NAME
I
M
B
K
_
_
_
0
OK or ERR
I
M
B
K
_
_
_
1
OK or ERR
A
D
J
S
_
_
_
1
OK or ERR
61
Return code (
Problem response (communication error or incorrect command)
E
R
R
Return code (
Projector
→
O
K
←
RETURN
03.2.4, 2:07 PM
0DH
)
0DH
)
61

Publicidad

Tabla de contenido
loading

Manuales relacionados para Sharp PG-A10X

Contenido relacionado para Sharp PG-A10X

Este manual también es adecuado para:

Pg-a10s

Tabla de contenido