Battery Charging; Changing The Tool - Bosch AdvancedMulti 18 Manual Original

Ocultar thumbs Ver también para AdvancedMulti 18:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 35
Fitting
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.

Battery Charging

Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
To remove the battery (4), press the battery release button
(5) and pull the battery to the rear and out of the power tool.
Do not use force to do this.
The following table shows examples of application tools. You can find additional application tools in Bosch's extensive range of
accessories.
Application tool
Bi-metal segment
saw blade
Sanding plate for
Delta series 93 mm
sanding sheets
Profile sander
Bi-metal plunge cut
saw blade for wood
and metal
Bosch Power Tools
Battery charge indicator
The battery charge indicator (3) indicates the remaining bat-
tery capacity or an overload when the power tool is switched
on.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Slowly flashing light 1 x green
If the battery charge indicator (3) flashes red, the power tool
is overloaded (see "Temperature-dependent overload pro-
tection", page 23).

Changing the tool

u
Selecting an Application Tool
Please observe the application tools intended for your power
tool.
Application tool
Material
Wood-based materials,
plastic, non-ferrous
metals
Depends on the sanding
sheet
Wood, pipes/profiles,
paint, varnish, filler, metal
Softwood, soft plastics,
plasterboard, thin-walled
aluminium profiles and
non-ferrous metal pro-
files, thin sheet metal,
Wear protective gloves when changing tools. There is
a risk of injury when touching the application tools.
Application
Separating cuts and plunge saw cuts;
including sawing close to edges, in corners and in difficult-
to-reach areas;
example: Shortening skirting boards that are already in-
stalled or door frames, plunge cuts when adapting floor
panels
Sanding surfaces at edges, in corners or in difficult-to-
reach areas;
depending on the sanding sheet, e.g. for sanding wood,
paint, varnish, stone;
fleeces for cleaning and for texturing wood, removing rust
from metal and for keying varnish, polishing felt for pre-
polishing
Convenient and efficient sanding of profiles up to a dia-
meter of 55 mm;
red sanding sheets for sanding wood, pipes/profiles, var-
nish, filler and metal
Small separating cuts and plunge cuts;
example: Cutting a recess for sockets, cutting a copper
pipe so that it is flush with a surface, making plunge cuts in
plasterboard
English | 19
Capacity
≥ 66%
33–66%
11–33%
≤ 10%
AdvancedMulti 18
1 609 92A 4N1 | (12.10.2018)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

3 603 a04 0

Tabla de contenido