Electrical Connection - Astralpool 10892 Manual De Instalación Y Mantenimiento

Concrete pool with liner (Fig. 6): Fit the protection cover to prevent ingress oi the concrete. Mount the seal and the
inserts ring at the rear of the niche for prefabricated pools and hold it in place using 2 screws. Before the next step, place
the adhesive sheet over the front part to prevent ingress of foreign bodies into the 10 yet to be used inserts. Bring the
concrete level to the niche mouth, position the gasket, fit the liner and tighten on the clamping ring using the 10 bolts.
The clamping ring should be positioned with its flat area towards the botton and symmetrical with the vertical axis,
PREFABRICATED POOLS.
The niche for prefabricated pools allows several mounting options depending on whether it will be used with panels or
plates and whether its is mounted from the outside or from the inside. In any case, the clamping ring should be positioned
with its flat area towards the bottom and symmetrical with the vertical axis.
To help with the Installation in the wall, an adhesive sheet is enclosed which can be used as a template.
Panelled pools (Fig, 7): Put a 31 Omm diameter hole in the panel. Fit the inserts ring from behind the panel and mount
it with screws, position the niche and gasket from the other side and hold It in place using 2 upper and lower screws. Fit
the other gasket, the liner and tighten down the clamping ring using the 10 screws.
Exterior mounting In plate pools (Fig, 8): Put a hole in the plate as shown in the drawing (Fig. 10) and fit the niche with
the gaskets and the inserts ring from the outside. Hold in place with the 2 screws top and bottom. Fit the gasket, the
liner and tighten down the clamping ring using the 10 screws.
Interior mounting in plate pools (Fig. 9): Put a hole in the plate as shown in the drawing (Fig. 10). pass the niche with its
gasket through the hole, Fit the Inserts ring with its gasket from behind and fix in place with the 2 upper and lower
screws. Fit the gasket, the liner and tighten down the clamping ring using the 10 screws.
5. POSITION OF THE ROTO-HUB (Fig. 11)
The angle at which the electric cable enters the niche can be chosen for ease of mounting.
The angle can be varied using the roto-hub which allows positioning every 45". There are therefore 8 possible
Undo the nut and remove the roto-hub from its position in the niche. Turn it to the required position and re-fit it into the
niche. Replace the nut, paying special attention to ensure that the 0-ring seal is correctly fitted, and hand tighten.
A PG-16 threaded socket is supplied for gluing into the roto-hub

6. ELECTRICAL CONNECTION

PAR Lamp (Fig. 13)
Loosen the niche and light cable gland nuts (6) in order to be able to pass the cable from the connections box through
the conduit. Be careful to allow some 2 m of cable so that the light can be trough! up to pool side to aid routine
maintenance. (Fig. 15)
Remove the 2 central screws (1) and the 10 nuts (2) which hold the face plate to the iamp housing.
Remove the bulb (3) along with its connections from the interior and wire up the 2 phases to the connection board (4).
Reassemble doing the above in reverse order taking care that the 0-ring (5) is in place and that all the nuts (2) are
properly lightened in the illustrated sequence.
Tighten the cable gland nuts (6) taking care to correctly position the seal (7) and the back-up ring in order to maintain
watertightness.
The connection cable should be of the type, with 2 filaments, with an external diameter of betwenn 10 and 14 mm and
with a wire section no less than 6 mm2.
7. LIGHT MOUNTING (Fig.12)
To mount the light in the interior of its niche start by winding the 2 m of electrical cable over the body of the lamp
housing.
Put the light into the interior of the niche, incline the face plate and fit its lower tag into the lower part of the niche (flat
area).
Position the upper screw through the face plate and tighten it to hold the light in place.
8. LIGHT INCLINATION (Figs. 15 and 16)
The light design allows a 4° of movement of the light beam with respect to the horizontal in order to prevent dazzling
outside the pool. (Fig. 14)
To carry out this inclination, remove the light from its niche and bring it up to poolside, Remove the central screws (3),
Separate the lamp housing (1) pressing forward the anchor clip (4) to leave the lamp housing free to separate it from the
face piale (2). Turn the lamp housing 180°,
Reassemble the lamp housing (1) with the face plate (2) by using the anchor clip (4), position the 2 central screws (3) with
their washers and tighten to leave the 2 parts of the light with the desired inclination.