Install Roof Cap, Wall Cap, Inline Or Remote Blower; Connect Ductwork; Install The Electrical Panel; Plan House Wiring - Thermador Masterpiece Serie Manual De Instalación

Ocultar thumbs Ver también para Masterpiece Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

I N S T A L L A T I O N
E
B
E
A
D
D
Clean housing surface (B) with Isopropyl Alcohol or Rubbing
Alcohol. Remove TAPE STRIPS to reveal adhesive side of tape from
the back side of TRIM BRACKET (A).
E
Center trim bracket left-to-right at TOP OF DOWNDRAFT
HOUSING (B). Stick trim bracket to downdraft housing so that
FLANGES (C) and (D) are l ush with each other.
F
Cut TRIM SEAL (E) to length: No shorter than downdraft countertop
cutout opening and no longer than cooktop width.
G
Remove tape backing from TRIM SEAL (E). Center trim seal
left-to-right and stick trim seal across both FLANGES (C) and (D).
Install roof cap, wall cap, inline or remote
blower
1. Follow instructions included with caps, inline and remote blower.

Connect ductwork

1. From roof cap, wall cap, or remote blower - work back towards the
cabinet, attaching all ductwork, elbows and transitions as previously
planned.
2. Connect ductwork (and transition, if required) to l ex blower or downdraft.
If necessary, use (2) no. 8-18 x .375 (9.5 mm) Phillips screws for transition.
Note: Regardless of blower placement/exhaust, ensure that all seams are
properly taped - to make them secure and air-tight. This includes seams/
gaps between panels and/or on the blower.

Install the electrical panel

(if previously removed from downdraft housing)
1. If electrical panel was removed from the downdraft housing in order to
mount it in a remote location: Mount electrical panel in chosen location.
Note: Do not mount electrical panel with slots in cover facing downward.
G
D
C
F

Plan house wiring

WARNING
RISK OF ELECTRIC SHOCK
Parts inside the appliance can have sharp edges. The connection
cable can be damaged. Do not bend or pinch connection cables
during installation.
Before connecting the appliance, check the house wiring to make sure
it has sufi cient circuit protection. The voltage and frequency of the
appliance must match the electrical installation (see rating plate).
Only a qualii ed electrician who takes the appropriate regulations into
account may lay or replace the connecting cable.
Follow all valid standards and laws.
Ensure that the electrical connection meets the requirements of the
latest version of all applicable standards and laws in the appropriate
country, especially the following standards:
National Electrical Code, ANSI/ NFPA 70, or CSA Standards C22.1-94,
Canadian Electrical Code, Part 1 and C22.2 No.0-M91, UL 507.
Have a qualii ed electrical technician check the grounding of the
appliance.
Do not ground to a gas line.
Keep these installation instructions for future reference.
Ensure that the wire diameter meets the requirements of the latest
version of all applicable standards and laws in the appropriate country,
especially the following standards:
National Electrical Code, ANSI/NFPA 70, or CSA Standards C22.1-
94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91.
The downdraft with the Flex Blower (purchase separately) draws 3.0 Amps
and requires a 120 VAC, 60 Hz circuit.
The downdraft with Remote Blower (purchase separately) draws 9.0 Amps
(max.) and requires a 120 VAC, 60 Hz circuit.
The downdraft has a 30-in. (762 mm). long power cord with a 3-pronged
plug. Plan to provide a grounded outlet in a location which will allow the
power cord to reach.
Page 19

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Ucvm30xsUcvm36xsUcvp36xs

Tabla de contenido