Using Featherboards; Non Thru-Sawing; Rabbeting; Dadoing - Bosch 4000 Instrucciones De Funcionamiento Y Seguridad

Ocultar thumbs Ver también para 4000:
Tabla de contenido

Publicidad

Non Thru-Sawing
Add 8" high fiat facing board to the fence, the full length of the
fence (Fig=42).
Use featherboards
for all "Non Thru-Sawing"
operations
(when
sawbtade guard must be removed). Featherboards 1 are used to
keep the work in contact with the fence and table as shown, and
to stop kickbacks.
Mount featherboards
1 to fence and table as shown, so that
leading edges of featherboards
wilI support workpiece until cut is
complete, and the workpiece has been pushed compbtely
past
the cutter (sawbtade, dado head, molding head, etc.) with a Push
Stick 2, as in ripping.
Before starting the operation (switch saw "OFF" and set cutter
below table surface):
A. install featherboards
so they exert pressure on the workpiece;
be positive they are securely attached.
B. Make sure by trial that the featherboards wilI stop a kickback if
one should occur.
Eeatherboards
are not employed
during
non thru-sawing
operations when using the miter gauge.
REPLACE THE SAWBLADE
GUARD AS SOON AS THE NON
THRU-SAWING OPERATION iS COMPLETE.
WON}(
SUPPORT
SUPPORT
APOYODELA
P_EZA DE
TNADAJO
Rabbeting
RABBETING is known as cutting out a section of the corner of a
piece of material across an end or along an edge (Fig=43).
Making a RABBET requires cuts which do not go all the way
through the material. Therefore the blade guard must be removed.
1. Remove blade guard.
2. For rabbeting along an edge (long way of workpiece) as shown,
add facing to rip fence approximately as high as the workpiece is
wide. Adjust rip fence and blade to required dimensions;
then
make first cut with board fiat on table, fot!ow set-up Fig. 42. Make
second cut with workpiece on edge, follow set-up Fig. 40. EoIIow
all precautions,
safety instructions, and operation instructions as
for ripping OF rip type operations,
including featherboards
and
Push Stick, etc.
3. For rabbeting
across
an end, for workpiece
10-1/2"
and
narrower make the rabbet cut with the board flat on the table.
Using the miter gauge fitted with a facing,
follow
the same
procedures and instructions
for crosscutting
making successive
cuts across the width of the workpbce
to obtain the desired width
of cut. DO NOT use the rip fence for rabbeting across the end.
4. INSTALL BLADE GUARD IMMEDIATELY UPON COMPLETION
OF RABBETING OPERATION.
Rabbet cuts can also be made in one pass of the workpiece over
the cutter using the dado head or molding head.
Dadoing
and Molding
Instructions
for operating
the Dado and Molding
Heads are
contained in booklet furnished with these accessories.
ALWAYS USE APPROPRIATE TABLE iNSERT LISTED UNDER
ACCESSORIES.
RABBET
F_HDT CUT
PDE_'H_:HE DOUPE
PDmMEB COBTE
\
\,
DECDNO BUT
OED×_:_'IE DOUPE
DEGUNOD CODTE
DABBET_NG ALONG
THE EDGE
H_:AUSAT_ON O'NNE
FEU_LLNDE LE LONGO'NN
BODO
HEBAJO A LO LADGO
OEL BODOE
/
DABBETINDA(;DOSS
THE END
DEAUSATION O'UNE
FEUmLLUHEEN TDAVEHS
D'UNE EXTHE_'IITE
HEDAJO THANSVEHSAL
AL EXTRE_'BO
50.

Publicidad

Tabla de contenido
loading

Tabla de contenido