Casals CAG7/115 Manual De Instrucciones página 4

any ad justments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
- Store idle power tool out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dan gerous in the hands of untrained
users
- Maintain power tools. Check for misalignment or
bind ing of moving parts, breakage of parts and any
other con dition that may affect the power tool's op-
eration. If dam aged, have the power tool repaired
before use. Many acci dents are caused by poorly
maintained power tools
- Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control
- Use the power tool, accessories and tool bits etc.
in ac cordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations dif-
ferent from those intended could result in a hazardous
situation.
Service
- Have your power tool serviced by a qualified re-
pair person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained
- Any misuse or failure to follow the instructions for use
renders the guarantee and the manufacturer's liability
null and void.
Safety warnings for angle Grinder
Safety Warnings Common for Grinding, Sanding,
Wire Brushing, or Abrasive
Cutting-Off Operations
- This power tool is intended to function as a
grinder, sander, wire brush or cut-off tool. Read
all safety warnings, instructions, illustrations and
specifications provided with this power tool. Fail-
ure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
- This power tool is not recommended for polish-
ing. Operations for which the power tool was not de-
signed may create a hazard and cause personal injury.
- Do not use accessories which are not specifically
designed and recommended by the tool manufac-
turer.
4
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
- The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed
can break and fly apart.
- The outside diameter and the thickness of your ac-
cessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
- The arbor size of wheels, flanges, backing pads or
any other accessory must properly fit the spindle of
the power tool. Accessories with arbor holes that do
not match the mounting hardware of the power tool will
run out of balance, vibrate excessively and may cause
loss of control.
- Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of the
rotating accessory and run the power tool at maxi-
mum no-load speed for one minute. Damaged ac-
cessories will normally break apart during this test time.
- Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron ca-
pable of stopping small abrasive or workpiece frag-
ments. The eye protection must be capable of stopping
flying debris generated by various operations. The dust
mask or respirator must be capable of filtrating particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
- Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear per-
sonal protective equipment. Fragments of workpiece
or of a broken accessory may fly away and cause injury
beyond immediate area of operation.
- Hold the power tool by insulated gripping surfaces
only, when performing an operation where the cut-
ting accessory may contact hidden wiring or its
own cord. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
- Position the cord clear of the spinning accessory.
If you lose control of the power tool, the cord may be cut
or snagged and your hand or arm may be pulled into the
spinning accessory.
- Nev
has c
sory m
of you
- Do n
side.
could
your b
- Reg
motor
exces
electr
- Do n
terial
- Do
ants.
electr
Kickb
- Kic
snagg
other
stallin
the un
oppos
bindin
or pin
is ent
of the
out. T
the o
move
may a
- Kick
corre
avoid
- Main
your
force
maxim
durin
tions
- Nev
sory.
- Do
powe
will p
move
- Use
edge
cesso
tende
loss o