Casals CAG7/115 Manual De Instrucciones página 8

- Block the spindle (F) by pressing the Spindle blocking
button (E). The spindle must be stopped before press-
ing the spindle blocking button.
- With the Tightening key (K) remove the clamping nut
(J) from the spindle (F).
- Assemble the tool on the support plate (H).
- Assemble the clamping nut (J) using the tightening
key (K). The position of the clamping nut (J) will depend
on the thickness of the tool (see fig 3 and 4).
- Once the tool is assembled check if the spindle block-
ing button (E) has return to its original position.
Use:
- Connect the appliance to the mains.
- Turn the appliance on, by using the on/off switch.
- Be careful of the shavings that fly off. Hold the tool
that so the sparks fly away from you, other people or
inflammable materials.
- When carrying out grinding operations, it is advisable
that the angle between the surface and the disc is ap-
proximately 15º - 30º for the best results.
- When cutting, do not press on the disc. The discs
should not move sideways or oscillate. The tool should
advance smoothly at the beginning and later moderate-
ly and adapted to the type of material. The tool should
move in the opposite direction to the advance of the
disc, never in the same direction, as there would be a
risk of the machine dumping out of the cutting line in an
uncontrolled manner.
Once you have finished using the appliance:
- Stop the appliance by releasing the on/off switch.
Cleaning
- Disconnect the appliance from the mains and allow it
to cool before undertaking any cleaning task.
- Clean the electrical equipment and the mains connec-
tion with a damp cloth and dry. DO NOT IMMERSE IN
WATER OR ANY OTHER LIQUID.
- Clean the equipment with a damp cloth with a few
drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or base
pH such as bleach, or abrasive products, for cleaning
the appliance.
- Do not let water or any other liquid get into the air
vents to avoid damage to the inner parts of the appli-
ance.
- Never submerge the appliance in water or any other
liquid or place it under running water.
- If the appliance is not in good condition of cleanliness,
its surface may degrade and inexorably affect the du-
ration of the appliance's useful life and could become
unsafe to use.
8
Supplies
- Always use original supplies, designed specifically for
your appliance model.
- These supplies are available in specialist shops.
Anomalies and repair
- Take the appliance to an authorised technical support
service if a product damage or other problems arise.
Do not try to dismantle or repair without assistance, as
this may be dangerous.
- If the connection to the mains has been damaged,
it must be replaced and you should proceed as you
would in the case of damage.
Specifications:
- Rated Power:
- Rated Voltage:
- No load Speed
- Max. disc diameter
- Spindle thread
- Weight:
Sound Pressure level:
Sound Power level:
Vibration:
NB: These specifications are subject to change without
notice of purpose of improvement.
NB: By virtue of the conditions of fabrication of this
product, the maximum absorbed power can differ from
that specified.
NB: By virtue of the conditions of fabrication of this
product, the maximum used power can differ from that
specified.
Wear hearing protection
- Measured sound level determined according
EN60745.
- The vibration emission level given in this information
sheet has been measured according EN60745 and
may be used to compare one tool with other. It may be
used for a preliminary assessment of exposure.
-The vibration value during actual use of the power tool
can differ from the declared total value depending on
the way in which tool is used.
-It's necessary identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to
the trigger time).
For E
reque
Ecolo
- The
consi
recyc
use th
of ma
- The
stanc
ronm
- This
memb
conce
CAG7/115
720W
230-240V~
11.000 rpm
115 mm
M14
1.75Kg
93 dB(A)
104 dB(A)
3.8m/s2 K=1.5m/s2