Canon imageCLASS MF4570dn Guia De Inicio Rapido página 25

CAUTION
▪ Keep the toner cartridges and other consumables out of the reach of small children. If the toner or other
parts are ingested, consult a physician immediately.
▪ Do not attempt to disassemble the toner cartridge. The toner may scatter and get into your eyes or mouth. If
toner gets into your eyes or mouth, wash them immediately with cold water and consult a physician.
▪ If toner leaks from the toner cartridge, be careful not to inhale the toner or allow it to come into direct contact
with your skin. If the toner comes into contact with your skin, wash with soap. If the skin becomes irritated or
you inhale the toner, consult a physician immediately.
▪ Do not pull out the sealing tape forcefully or stop at midpoint, as this may cause toner to spill out. If toner
gets into your eyes or mouth, wash them immediately with cold water and consult a physician.
Others
WARNING
▪ If you are using a cardiac pacemaker
This machine generates a low level magnetic fi eld. If you use a cardiac pacemaker and feel abnormalities,
please move away from this machine and consult your physician immediately.
Telephone Equipment
When using telephone equipment, basic safety precautions should always be followed to reduce the risk of fi re,
electric shock, and injury to persons, including the following:
1. Do not use this machine near water (i.e., near a bathtub, kitchen sink, or laundry tub), or in a wet basement
or near a swimming pool.
2. Avoid using the telephone during an electrical storm, as there may be a remote risk of electric shock from
lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
Installation Requirements and Handling
In order to use this machine in a safe and trouble-free manner, install the machine in a place that fulfi lls the
following conditions. Also, read the remarks carefully.
Temperature and Humidity Conditions
▪ Temperature range: 10 to 30°C (50 to 86°F)
▪ Humidity range: 20 to 80 % RH (no condensation)
IMPORTANT
Protecting the machine from condensation
▪ To prevent condensation from forming inside the machine in the following cases, let the machine adjust to
the ambient temperature and humidity for at least two hours before use.
- When the room where the machine is installed is heated rapidly
- When the machine is moved from a cool or dry location to a hot or humid location
▪ If water droplets (condensation) form inside the machine, this can result in paper jams or poor print quality.
When using an ultrasonic humidifi er
When you are using an ultrasonic humidifi er, it is therefore recommended that you use purifi ed water or other
water that is free of impurities.
If you use tap water or well water, impurities in the water will be dispersed through the air. This can be trapped
inside the machine, causing degradation in print quality.
Power Supply Requirements
120 to 127 V, 60 Hz
IMPORTANT
Precautions when connecting the power cord
▪ Do not connect this machine to an uninterruptible power source.
▪ Use an AC power outlet exclusively for the machine. Do not use the other sockets of the AC power outlet.
▪ Do not plug the power plug into the auxiliary outlet on a computer.
Do not use the same AC power outlet for both the machine and any of the following equipment.
- Copy machine
- Air conditioner
- Shredder
- Equipment that consumes a large amount of electricity
- Equipment that generates electrical noise
▪ When unplugging the power cord, keep interval of 5 seconds or more before plugging it again.
Miscellaneous precautions
▪ The maximum power consumption of the machine is 1,090 W or less.
▪ Electrical noise or a dramatic drop in supplied voltage may cause the machine or computer to operate
incorrectly or lose data.
Installation Requirements
▪ A location with suffi cient space
▪ A location with good ventilation
▪ A location with a fl at, even surface
▪ A location able to fully support the weight of the machine
IMPORTANT
Do not install the machine in the following locations, as this may result in damage to the machine.
▪ A location subject to dramatic changes in temperature or humidity
▪ A location subject to condensation
▪ A poorly ventilated location
(If you use the machine for a long time or to perform a large amount of printing in a poorly ventilated room,
the ozone or other odors generated by the machine may create an uncomfortable working environment.
In addition, chemical particles are dispersed during printing; therefore, it is important to provide adequate
ventilation.)
▪ A location near equipment that generates magnetic or electromagnetic waves
▪ A laboratory or location where chemical reactions occur
▪ A location exposed to salt air, corrosive gases, or toxic gases
▪ A location, such as on a carpet or mat, that may warp from the weight of the machine or where the machine
is liable to sink.
5
English