Juliana Grand Oase Manual De Instrucciones página 4

May we congratulate you on your new greenhouse
GB
Dear Customer! DEAR CUSTOMER
Congratulations on purchasing your new
The assembly of your new house requires
greenhouse. It is important that you follow these
a bit of technical knowledge. However, it is
assembly instructions step-by-step.
important that the assembly instructions are
followed strict-ly. The assembly instruction
The assembly instructions are a combination of text
is a combination of text and illustrations. The
and illustrations. The profiles are packed in separate,
profiles are packed in separate numbered packs
numbered packs corresponding to their order of use
in the instructions. Assemble one pack at a time. All corresponding to the order in the assembly
nuts, bolts and fittings are contained in a Box.
instruction. Erect one pack at a time. All nuts
Each pack is specified in separate lists of
and bolts and fittings are found in bag No. 0
components.
(specified on page 12). Each pack is specified in
All detailed illustrations are marked with the
separate lists of components.
following symbols:
All detailed illustrations are marked with
symbols:
Seen from the inside Seen from the outside
Seen from inside Seen from outside.
SOME SAFETY PRECAUTIONS
• Assembly must only be carried out in dry and
calm weather.
Precautions.
• Always wear work gloves when installing the
• Assembly must only be carried out in dry
glazing. Greenhouse glass has sharp edges,
and calm weather.
especially if it breaks.
• Always use working gloves while glazing.
• Assistants and especially children must be
Greenhouse glass has sharp edges,
warned that broken glass is dangerous. Pick
especially if the glass breaks.
up all broken glass at once and remove it with
• Assistants and especially children must be
care.
• We recommend that you wear protective
warned that broken glass is an element of
glasses while fixing the spring wire clips.
danger. Pick up broken glass at once and
• Any ladders that are used must be placed on a
remove it with care.
level surface.
• We recommend to use protective glasses
• It is essential to have an assistant available.
while fixing the spring wire clips.
• Place the ladder on a level support.
PAGE 12: TOOLS
• It is essential to have an assistant.
Assembling the greenhouse requires the tools
shown on page 12.
References
PAGE 15: FOUNDATIONS
The column marked indicates the
No base is included with this product. However, an
page(s) on which the component is used.
original base is available separately. This base is easy
to construct and will guarantee you a stable base for
Page 13:
your greenhouse.
Foundation
If you construct your own base, the specified
The base is not included in this delivery.
measurements must be external measurements.
However, an original base can be bought
The holes must be dug out to below the frost line
(800 mm). Place the assembled base with anchor
separately. It ensures you a stable and easy to
legs over the holes so the anchor legs fit into the
build base.
holes; it takes about 75 litres of concrete to fill up
If you make your own base the measurements
the holes.
indicated must be external measurements.
Make sure the base is completely level and square.
If you buy an original base you furthermore
To square the base, make sure the two diagonal
need about 75 litres of concrete and 6/8
measurements are identical.
plastic-/concrete pipes of about 800 mm which
The width of the front and back gables must also be
are placed in a non-freezing depth for the
identical.
fastening of the corner and middle anchors.
ATTACHMENT TO THE BASE
The base must be 100% level and square; the
If you construct your own base, you must drill holes
latter is ensured by checking that the two
(7mm) in the ground frame between all the vertical
diagonal measurements are equal.
profiles. The greenhouse must then be secured to
the base using screws (A).
Tools
If you use an original base, the greenhouse must be
The mounting of the greenhouse requires the
secured to each vertical bar as shown on drawings
tools shown on page 12.
B/C.
PAGE 14-27: ORDER OF ASSEMBLY
Page 14-27:
Place the components as shown on the illustration
Place the components as shown on the
and assemble in the order shown in the pictures. Do
illustration and assemble in the order shown
not tighten the nuts fully until the entire sub-frame
in the pictures. Do not tighten the nuts
has been assembled.
completely until the front gable construction
has been assembled.
Page 13:
PAGE20-27 : ROOF
(Fastening to the base).
The cylinder allows travel of 20–30 mm for the hood.
When constructing your own base you have
The actual cylinder can be moved up and down. If
to drill holes (7 mm) in the ground frame
the rod is in the lowest position, the travel will be
between all the vertical frames, the greenhouse
greatest. If the cylinder is moved upwards, there will
is then fastened to the base with screws (A).
be less travel.
Using an original base the greenhouse is
If you wish to close the hood completely, move the
fastened to each vertical bar as shown on
cylinder to its lowest position and lock it in place by
turning the screw towards the cylinder. Do not over- drawing B/C.
tighten the screw.
Page 24-27:
PAGE 28-31: DOORS AND WINDOWS
For an easier assembly we recommend that you
For easier assembly, we recommend that you oil the
oil the screws for the doors.
screws for the doors. The glass or polycarbonate for
the door(s) and windows must be fitted at the same
Fitting of glass/polycarbonate
time as the profiles.
Important before glazing!
PAGES 32-35: FITTING OF GLASS
Make sure that gables and sides are level and
Important before assembly!
square, and that door(s) and window(s) are
Make sure that the gables and sides are level
functioning perfectly.
and square and that door(s) and window(s) are
functioning perfectly.
Best order of assembly:
1) Windows – 2) Roof – 3) Doors – 4) Gables
The best order of assembly for the glass:
– 5) Sides
Windows - Doors - Roof - Gables - Sides
Glass installation (illustrations 1 to 8)
Page 30-33:
Degrease the sheets and frames with spirit.
Glazing (illustration 1 to 8)
Start glazing from the bottom, one pane at a time.
Degrease the sheets and frames with spirit.
Apply a 3mm silicone bead around the vertical
Start glazing from below, one glass at a time.
frames as indicated (the dotted lines on the
Apply a 3 mm silicone line on the vertical
illustration). (A 3mm bead of silicone is sufficient to
frames where indicated (dotted lines on
ensure maximum adhesion). If you use more silicone
the illustration). (A 3 mm line of silicone is
than recommended, extra tubes can be purchased.
sufficient to obtain maximum attachment). If
If you accidentally break a pane, carefully pull the
you do use more than recommended, you can
broken glass outwards and loosen the silicone using
buy extra tubes.
a sharp craft knife.
Clean the profile completely before inserting a new
Spring wire clips and glassholders are to be
pane of glass.
fitted as shown.
X = Spring wire clips, > = Glassholders
M-strips are fitted as shown on pages 29. Place the
upper part of the strip under the aluminium profile
In case of broken glass carefully pull it
along the full length of the sheet and then click the
strip into position from above.
outwards and loosen the silicone by means of a
sharp craft knife.
Your greenhouse is now fully assembled. However,
Clean the profile completely before inserting a
please note the following:
new pane of glass.
MAINTENANCE
Page 34-37:
• Grease the doors (hinges and locks).
Mounting of polycarbonate
• Keep the gutters free from leaves, etc.
The illustrations at the bottom of page 34/36 • Adjust the windows as necessary.
• Replace any broken glass.
show where to mount the polycarbonate plates
• Clean the greenhouse with disinfectant before
and lists. The type indication states the length
and after the growing season.
in mm. A possible adjustment is made by
means of a fine-tooth saw.
WINTER PROTECTION
NB! To avoid the formation of algae the
If you anticipate snow during the winter, we
polycarbonate sheets must not come into
recommend the following winter precautions:
contact with the ground. Rest them on a piece
• Support the apex of the roof in the middle.
• of cardboard. Remove any deep snow from the roof.
• Take precautions to prevent snow falling from
a tree or roof, for example.
A-lists are mounted as shown on page 35/37.
• Adjust the cylinders for the opening of the
Put the sheet into the bottom list, bend the
hood.
sheet slightly outwards and put it in the top list.
• Secure the door(s) and window(s) to prevent
wind damage to the greenhouse.
M-lists are mounted as shown on page 35/37.
Place the upper part of the list under the alu.
profile in the whole length of the sheet and
hereafter click on the list from above.
WATER AND CONDENSATION
B
Please note that your greenhouse is not like a
Sealing of the polycarbonate sheets
conservatory, for example, and that you should
The sheets may be sealed against insects.
therefore be aware that the greenhouse may leak
Close the top end off with alu-tape or silicone.
during or after precipitation and that condensation
The bottom only with airstrip tape to let
will occur on the inside of the greenhouse. Good
condensation out (available at your local
ventilation will help prevent condensation.
dealer).
INSURANCE
Please note that not all insurance companies cover Now your greenhouse is completely assembled.
greenhouses automatically. Please contact your
However, please notice the following:
insurance company to ensure that your greenhouse
is covered.
Maintenance
• Grease doors (hinges and lock).
GUARANTEE
• Clean the gutter for leaves, etc.
Juliana greenhouses are covered by a 12-year
• Adjustment of windows.
guarantee, which covers the replacement or repair
• Replacement of broken glass.
of faulty parts. The guarantee does not cover
polycarbonate, glass, transport, assembly, freight,
• Clean the house with disinfectant before
etc.
and after the growing season.
Juliana greenhouses are covered by a two-year
warranty on painted parts, where fitted. Note that
Winter Protection
marks on the paint may occur due to suspension of
In areas with occurrence of snow we
the profiles.
recommend the following winter protection:
The guarantee will be void if the greenhouse is not
• Support the roof ridge at the centre of the
assembled in accordance with these instructions.
house.
COMPLAINTS
• Remove greater snow loads from the roof.
All our greenhouses are built to the highest quality
• Take precautions against snow falling
standards. However, should you experience any
down from for instance a tree or a roof.
problems, please contact your dealer at once. When
• Dismount the cylinders for the automatic
describing the defect, please state the greenhouse
window openers, if any (optional extras).
model, the component number.
• Secure door(s) and window(s) preventing
wind damage to the house.
Any suspension marks or shiny ends on painted
Juliana profiles will not be visible after the
greenhouse has been assembled. Insurance
Please note that not all insurance companies
Congratulations on your new greenhouse, which we
cover glasshouses automatically. Please
hope will bring you a lot of pleasure for many years
contact your insurance company to ensure an
to come.
insurance coverage.
Yours sincerely,
Guarantee
Juliana grants a guarantee of 12 years which
Juliana Drivhuse A/S
covers replacement of faulty parts. The
guarantee does not cover polycarbonate, glass,
transport, assembly, freight etc.
Juliana grants a guarantee of 2 years on painted
parts, if any. Note that marks in the painting
may occur due to suspension of the profiles.
The guarantee is invalid if the greenhouse is
not assembled according to these instructions.
Complaints
All our greenhouses are built to high standards
of quality. However, should a complaint
occur please contact your dealer at once.
Remember to specify the defect by indicating
the greenhouse model and number of the
component and the quality control number.
USA