Beninca THINKY Manual De Instrucciones página 14

The radio receiver in this product is compatible only with the new ARC (Advanced Rolling Code) transmitters which, thanks to 128-bit encryption
ensure superior copy-security. Storing new ARC transmitters is quite similar to that of normal rolling code transmitters with HCS coding
1) INPUT/OUTPUT FUNCTIONS
Terminal No. Function
1-2-3 Motor
4-5 Flashing light
5-6 AUX
Auxiliary
7-8
capacitor
9-10 Courtesy light
11-12 24Vac
13-14 SCA/PhotoTest
15 COM
16 SWO
17 SWC
18 PHOT 1
19 PHOT 2
20 PHOT 3
21 PHOT 4
22 STOP
23 OPEN
24 CLOSE
25 PED
26 Step-by-step
27 COM
28-29 DAS
30-31 Aerial
32-33 2 radio channel
nd
34-35 SAFETY
Selection of Mains
36-37-38
power supply
Single-phase power
39-40
supply
Three-phase power
39-40-41
supply
ENC ABS Absolute encoder
Connector
THINKY P
THINKY P
14
ARC CONTROL UNIT
IMPORTANT, PLEASE READ CAREFULLY:
THINKY Control Unit
Description
Connection, 230Vac motor - single-phase:
1-Movement+capacitor/2-Common/3-Movement+capacitor
Connection, 400Vac motor - three-phase:
1-U/2-V/3-W
Check that the voltage selection jumper on terminals 36-37-38 is correctly positioned.
Connection of flashing light, 230Vac 40W max.
Connect a negative electric brake to this output.
WARNING: Output, 230Vac 0,5A max. see AUX1 logic.
Output N.O. (10A max) for pickup auxiliary capacitor. See wire diagram.
WARNING: 230Vac motor - single-phase only.
DISG Logic must be set ON
Free N.O. contact (2A 150W) to control the Courtesy light which is timed according to the TLS parameter.
Output, accessory power supply 24Vac/0,5A max
Output, 24Vac/0,5A max. This can be preset as open gate indicator light or as checked devices power
supply (PhotoTest) through the TSTP logic.
In the event of presetting as PhotoTest, please refer to the diagram "Connection of checked safety
devices"
Common for limit switches and photocells and to all control inputs.
Input, OPEN limit switch (N.C. contact)
Input, CLOSE limit switch (N.C. contact)
Input, Photocell 1 (N.C. contact). It can be disabled in the opening phase, see PHO1 logic.
Input, Photocell 2 (N.C. contact). It can be disabled in the opening phase, see PHO2 logic.
Input, Photocell 3 (N.C. contact). It can be disabled in the opening phase, see PHO3 logic.
Input, Photocell 4 (N.C. contact). It can be disabled in the opening phase, see PHO4 logic.
Input, STOP push-button (N.C. contact)
Input, OPEN push-button (N.O. contact).
Input, CLOSE push-button (N.O. contact)
Input, pedestrian push-button (N.O. contact)
Input, step-by-step (N.O. contact)
Common for all other control inputs.
Input, safety edge contact.
Resistive edge: closed " DAS" jumper.
Mechanical edge: open "DAS" jumper.
When the safety edge is activated, the gate movement stops. The gate movement is reversed for ap-
proximately 3 sec if the INVA logic is ON. If no safety edge is used: "DAS" Jumper open, jumper be-
tween terminals 28-29.
Connection of the antenna to the receiver extractable board (30-signal/31-screen).
Output, 2 radio channel of the two-channel extractable receiver.
nd
Emergency stop connection. WARNING: Mains power supply.
Remove the jumper and connect a N.C., changeover switch, suited for the mains voltage. See wire
diagram.
Selection of power supply voltage, short-circuit:
36 and 37 for three-phase power supply (400Vac)
37 and 38 for single-phase power supply (230Vac)
Input, single-phase mains power supply 230Vac/50Hz (39-L / 40-N)
Input, or three-phase mains power supply, 400Vac/50Hz (39-R / 40-S / 41-T).
Quick connector for connecting the control buttons on the central unit box in the THINKY P. version
IMPORTANT: If using the Absolute Encoder, Jumper J9 must be OPEN.
If not using the Absolute Encoder, Jumper J9 must be CLOSE.
Quick connector for connecting the control buttons on the central unit box in the THINKY P. version
IMPORTANT: If using the THINKY P connector, Jumper J8 must be OPEN
If not using the THINKY P connector, Jumper J8 must be CLOSE