LEGRAND Wattstopper FSP-221B Instrucciones De Instalación

No: 22599 – 10/18 rev. 7
Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: FSP-221B, FSP-221B-S, FSP-221B-D
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
Voltage .....................................100–347VAC (single phase)
Load Ratings
Wiring
Operating Temperature .......... -40°F (-40°C) to 167°F (75°C)
Tightening Skirt/Nut Torque ................................ 25–30 in-lbs
Dimensions
Weight .............................................................. 2.8 oz (80 g)
Enclosure ................................................. IP66 (NEMA STD)
Coverage
The FSP-221B is an IP66 rated motion sensor that dims lighting
from high to low based on movement.
Three configurations are available. The FSP-221B mounts inside
the fixture and the PIR lens connects to the FSP-221B through a
1.30" diameter hole in the bottom of the fixture. The FSP-221B-S
mounts to a fixture/enclosure with a 1/2" knock out, via a nipple on
the back. The FSP-221B-D has a drop mount nipple, for mounting
on to a pole, or to a fixture.
The sensor uses passive infrared (PIR) sensing technology that reacts
to changes in infrared energy (moving body heat) within the coverage
area. Once the sensor stops detecting movement and the time delay
elapses, lights will go from high to low mode and eventually to an OFF
position if it is desired. Sensors must directly "see" motion of a person
or moving object to detect them, so careful consideration must be
given to sensor luminaire placement and lens selection. Avoid placing the sensor where obstructions may block the sensor's line of sight.
The FSP-221B operates at 100–347V Single Phase, as well as 208/230/480VAC phase-to-phase. No power pack is required. It is
designed to be installed in indoor and outdoor environments.
NOTE: When the FSP-221B is powered up the first time, it the will use factory default parameters to operate. If adjustments are
needed, the FSIR-100 configuration tool must be used.
SPECIFICATIONS
............................. 208/230/480VAC phase-to-phase
@ 230–240V ..................0–300W Ballast or LED Driver
@ 120V .......0–800W Tungsten, Ballasts or LED Driver
@ 277V ........................0–1200W Ballast or LED Driver
@ 347/480V .................0–1200W Ballast or LED Driver
Motor @ 120V/277V............................................1/6 HP
Length .......36" (91.44cm), 30" (76.2cm) from nipple
Line Voltage .................................... Line, Neutral, Load
Low Voltage ............Dim + (violet), Dim - (gray) 18AWG
Collar ...................................... 1.30" diameter (33.0mm)
Collar height .......................................... 0.64" (16.3mm)
Body .....5.7"L x 2.3"W x 3.5"H (145mm x 60mm x 90mm)
FSP-L2 Lens @ 8' height .................. up to 44' diameter
FSP-L3 Lens @ 20' height ................ up to 40' diameter
FSP-L7 Lens @ 40' height .............. up to 100' diameter
DESCRIPTION AND OPERATION
Wattstopper
Single/Dual Phase (Universal), High/Low/Off,
PIR Fixture Integrated Outdoor Sensor In IP66 Enclosure
Monophasé/Biphasé (Universel), Haut/Bas/Éteint,
Luminaire avec capteur IRP extérieur intégré dans un boitier IP66
Fase simple/doble (universal), Alto/Bajo/Apagado,
Sensor exterior integrado del aplique PIR en gabinete IP66
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
Adjustments and Features
High Mode ......................................................0 V –10 V
Low Mode ............................................. 0 V – 9.8 V, Off
Time Delay .........................30 seconds, 1 min – 30 min
Cut Off ....................Disable, 1 min – 59 min ,1 hr – 5 hr
Sensitivity .....................On-Fix, Off-Fix, Low, Med, Max
Hold Off Setpoint ..........................Auto, None, 1–250 fc
Ramp Up .................................. Disable, 1 sec – 60 sec
Fade Down ............................... Disable, 1 sec – 60 sec
Photocell Setpoint for On/Off ...........................1–250 fc
Factory Defaults
High Mode .............................................................. 10 V
Low Mode ................................................................ 1 V
Time Delay ............................................................5 min
Cut Off ..................................................................... 1 hr
Sensitivity ...............................................................Max
Hold Off Setpoint ...............................................Disable
Ramp Up ............................................................Disable
Fade Down .........................................................Disable
Photocell Setpoint for On/Off .............................Disable
PIR Sensor
Motion Indicator
Red LED
Sensor Protection Cap
NOTE: Remove Cap before use
®
Light Sensor
IR Transmitter
IR Receiver