Designation; Nominal Calorific Power; Description And Dimensions; Description - deville C077AP Instrucciones Para La Instalación Y El Uso

You are advised to have a thorough and
careful reading of the instructions for use in
order to get the best use and satisfaction of
your DEVILLE appliance.
The fact of not respecting the fixing, the
installing and the use istructions involves the
responsibility of the person who doesn't
respect them.
THIS STOVE MUST BE INSTALLED IN
ACCORDANCE TO THE CURRENT D.T.U.
SPECIFICATIONS..
The stove must be installed by a skilled
professional.
All the local and national regulations as well
as the European standards have to be
respected when the stove is used.
The appliance mustn't be modified.

1 - DESIGNATION

Your DEVILLE appliance complies with the essential
requirements of Directive 89/106/EEC Construction
Products according to Appendix ZA of the EN 13240
Standard.
It is an intermittent and continuous combustion heat
appliance using a grate that operates exclusively using
wood, with a half-closed combustion chamber.
Note down the serial number written on the descriptive
plate stuck on the appliance and on the certificate of
guarantee, write it down in the following box :
Serial number
This number will be necessary to identify your appliance
when spare parts will be needed.
2 – CALORIFIC NOMINAL POWER
Nominal Draught Smoke output / weight
power
11 kW 12 Pa
Intermittent and continuous running :
The intermittent running needs a reload every three
quarters of an hour.
This choice of operation is to be favoured as it is
environmentally-friendly.
The appliance can also ensure a continuous running
when the intemittent constraints can't be respected or
when a reduced power is wanted.
Nominal calorific power with an intermittent working :
. Obtained under a draught of 12 Pa, during a 45-
minute fire period, with a load of 2,62 kg of hard wood
(hornbeam, oak, and so on) in the form of two split
wooden logs of about 8-11cm in diameter.
. To get this heat power, reload on an ash bed of about
300 g that is to say 3 cm thick.
Smoke
temperatures
8,5 g/s 384°C
The given power is the average power obtained in the
tests with the air intake damper opened to its
maximum.
The slow combustion :
. Obtained with a 6 Pa draught, with the air intake
damper closed
. Reload on an ash bed of about 300 g (3 cm thick).
. Duration in excess of 10 hours with an unsplit, 5.3 kg,
15 cm hard wood log.
Normal speed conditions allow to get a maximum
power which is not to be exceeded to guarantee a
running in complete safety.
The maximum loading is 15 kg of wood.

3 - DESCRIPTION AND DIMENSIONS

3.1 - Description

The top of your appliance is painted, do not place
anything on it as this could deteriorate it.
Fig. 1
The main elements constituting the stove are indicated
below :
(1) Handle
(2) Loading door
(3) Top
(4) Tube
(5) Rear screen
(6) Air adjustment knob
(7) Nozzle damper
(8) Ø 80 nozzle for external combustion air intake
A secondary air intake is incorporated into the upper
part of the door window in order to keep it clean and to
ensure better combustion of the wood.
The air regulation lever, located at the bottom, is used
to select a burning speed.
Net weight of the appliance
Gross weight (without door,
deflector, grate, vermiculite, top)

3.2 - Dimensions

Fig. 2
3.3 – Smoke duct connection to the rear (Fig.3)
Your appliance is configured for a connection of the
smoke ducts on the top, however, it is possible to alter
it for a connection at the rear if necessary:
Lift and remove the rear screen , remove the
-
pre-cut part by drilling in the 3 small holes. (Ø6
drill bit). Fig. 3a.
Open the door and remove the 5 nuts H (7mm
-
box wrench) which are housed in the openings
J Fig. 3b.
Remove the top
-
- Remove the 2 top screens .
12
C077AP
128 kg
86 kg
Fig. 3a.