Tabla De Contenido; Receiving And Uncrating; How To Order Replacement Parts - HYTROL 190-ACC Manual De Instalación Y Mantenimiento

TABLE OF CONTENTS
INTROdUCTION
Receiving and Uncrating . . . . . . . . . . . . . . . . . . . .2
How to Order Replacement Parts . . . . . . . . . . . . .2
SAfETY INfORmATION
Installation Safety Precautions . . . . . . . . . . . . . . .3
Operation Safety Precautions . . . . . . . . . . . . . . . .3
maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
INSTALLATION
Support Installation . . . . . . . . . . . . . . . . . . . . . . . .4
Ceiling Hanger Installation . . . . . . . . . . . . . . . . . .4
Conveyor Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . .4
Connecting the V-Belts . . . . . . . . . . . . . . . . . . . . .5
Belt Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Racked Sections . . . . . . . . . . . . . . . . . . . . . . . .6, 7
Electrical Equipment . . . . . . . . . . . . . . . . . . . . . . .6
Pressure Adjustment . . . . . . . . . . . . . . . . . . . . . . .7
OPERATION
Conveyor Start-Up. . . . . . . . . . . . . . . . . . . . . . . . .7
mAINTENANCE
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Belt Replacement . . . . . . . . . . . . . . . . . . . . . . . 8,9
drive Chain Alignment and Tension . . . . . . . . . . .9
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . .10
maintenance Checklist . . . . . . . . . . . . . back cover
External Slave drive . . . . . . . . . . . . . . . . . . . . . .10
REPLACEmENT PARTS
Slave Connection Parts drawing & List . . . . . . .11
model 190-ACC Parts drawing . . . . . . . . . . . . . .12
model 190-ACC Parts List. . . . . . . . . . . . . . . . . .13
model 190-LRC 90 deg Parts drawing & List. . .14
model 190-LRC 60 deg Parts drawing & List. . .15
model 190-LRC 45 deg Parts drawing & List. . .16
model 190-LRC 30 deg Parts drawing & List. . .17
model 190-LRS 45 deg Parts drawing & List. . .18
model 190-LRS 30 deg Parts drawing & List. . .19
model 190-LRSS 45 deg Parts drawing & List .20
model 190-LRSS 30 deg Parts drawing & List .21
Sub Assemblies and Parts List . . . . . . . . . . . 22,23
Sheave Retainers drawing & Parts List . . . . . . .23
Spanish Version . . . . . . . . . . . . . . . . . . 24
INTRODUCTION
This manual provides guidelines and procedures for installing, oper-
ating, and maintaining your conveyor. A complete parts list is pro-
vided with recommended spare parts highlighted in gray. Important
safety information is also provided throughout the manual.
safety to personnel and for proper operation of your conveyor, it is
recommended that you read and follow the instructions provided in
this manual.

• Receiving and Uncrating

1. Check the number of items received against the bill of lading.
2. Examine condition of equipment to determine if any damage
occurred during shipment.
3. move all crates to area of installation.
4. Remove crating and check for optional equipment that may be
fastened to the conveyor. make sure these parts (or any foreign
pieces) are removed.
NOTE: If damage has occurred or freight is missing,
Contact your Hytrol Integration Partner.

• How to Order Replacement Parts

Included in this manual are parts drawings with complete replace-
ment parts lists. minor fasteners, such as nuts and bolts, are not
included.
When ordering replacement parts:
1. Contact dealer from whom conveyor was purchased or nearest
HYTROL Integration Partner.
2. Give Conveyor model Number and Serial Number or HYTROL
factory Order Number.
3. Give Part Number and complete description from Parts List.
4. Give type of drive. Example-8" End drive, 8" Center drive, etc.
5. If you are in a breakdown situation, tell us.
Hytrol Conveyor
Company, Inc.
JONESBORO, ARKANSAS
SERIAL #
HYTROL Serial Number
(Located near drive on Powered models).
2
for
Model
Model
XX
123456