Setting Up Input3 And Input4 - Pioneer PDA-5001 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

Setting up INPUT3 and INPUT4

After components have been connected to INPUT3 or
INPUT4, on-screen setup is necessary.
Follow the procedure described below and make settings
as they apply to the type of components connected.
1
Switch MAIN POWER on the connection panel to
the on position to turn on the monitor's main
power.
The STANDBY/ON indicator lights red.
2
Press
STANDBY/ON to put the monitor in the
operation mode.
The STANDBY/ON indicator turns green.
3
Select INPUT3 or INPUT4.
4
Press MENU to display the menu screen.
The menu screen appears.
5
Press 5/∞ to select SET UP, and press SET.
M A I N
M E N U
P I C T U R E
S C R E E N
A L L
R E S E T
P OW E R
S A V E
S E T
U P
M E N U : M E N U
O F F
: S E L E C T
S E T : N E
6
Press 5/∞ to select SETTING.
S E T
U P
T E R M I N A L
: B N C
S E T T I N G
: V I D E O
S I
G
N A L
: R
G B
C
L A M
P
: M O
C
O
N T
R
A
H
I
G
H
E X I T
: S E L E C T
S E T : C H
Please note that the TERMINAL setting is set to
"BNC" when INPUT3 is selected, and "D-SUB" when
INPUT4 is selected.
7
Press SET to select either "PC" or "VIDEO".
When a personal computer is connected, set to "PC".
When a component other than a personal computer is
connected, set to "VIDEO".
Note
Steps 6 to 7 are necessary when inputting a signal of horizontal
frequency 31.5 kHz/vertical frequency 60 Hz.
For signals of other frequencies, settings are done automatically,
and therefore cannot be performed.
X T
D
E
1
:
S
T
O
F F
A N
G E
Setting Up the System
8
Press 5/∞ to select SIGNAL.
S E T
U P
T E R M I N A L
: B N C
S E T T I N G
: V I D E O
S I G N A L
: R
G B
C L A M P
: M O D E 1
R
A S T
H
I G
H
C
O
N T
E X I T
: S E L E C T
S E T : C H
9
Press SET repeatedly to select the input signal
format.
Selection will change as follows each time SET is
pressed.
RGB
COMPONENT 2
The table below shows what settings are appropriate
and available for the type of connections made.
10
When the setup is completed, press MENU to exit
the menu screen.
Notes
÷ Make this setup for each input (INPUT3 and INPUT4).
÷ When selecting a PC signal or when SETTING is set to "PC",
"COMPONENT" cannot be selected.
÷ Please refer to page 16 for details concerning CLAMP (G ON
SYNC) setup.
Set SETTING and SIGNAL as follows.
SET UP
SETTING
Connected
component
Component video output
VIDEO
of a DVB set top box
Component video output
VIDEO
of a DVD player, etc.
RGB video output of a
VIDEO
video deck etc., with RGB
output
RGB video output of a PC
PC
* Select either COMPONENT 1 or 2 depending on which setting
provides the most natural picture color for the component
connected.
Note
When a DVB set top box is connected, please also refer to the
instruction manual supplied with the set top box.
:
O
F F
A N G E
COMPONENT 1
SIGNAL
COMPONENT 1*
COMPONENT 2*
RGB
RGB (Fixed to RGB
when SETTING is set
to "PC".)
15
<ARE1351> En

Publicidad

Tabla de contenido
loading

Tabla de contenido