Memory Deletion; Additional Information - Nice Neomat T Serie Manual De Instrucciones

4.4) Memory deletion

If you need to delete all the transmitter and the programmed operations, carry out the procedure shown in table A14.
The memory can be deleted:
• with a non-memorized transmitter starting from point A.
• with a previously memorized transmitter starting from point No. 1.
The following can be deleted:
• only the memorized transmitters, finishing at point No. 4
• all data (transmitters, sensor level, TTBUS address, etc.), completing the procedure until point 6.
Table "A14" Memory deletion
➨
A. Switch the motor off, activate the Step-by-Step input (by connecting the White cable
with the White/Black one) and keep it active until the end of the procedure
B. Power the motor and wait for the initial beeps
➨ Press and hold down button ■ on a transmitter (about 5 seconds) until you hear
1.
a beep; then release it
Hold down the ▲ button on the transmitter until you hear 3 beeps;
2.
release the ▲ button exactly during the third beep
Hold down button ■ on the transmitter until you hear 3 beeps;
3.
release button ■ exactly during the third beep
➨ Hold down the ▼ button on the transmitter until you hear 3 beeps;
4.
release the ▼ button exactly during the third beep.
5. To cancel everything:
Press both ▲ and ▼ within 2 seconds
Cancellation is confirmed by releasing buttons ▲ and ▼ on the first of the 5 beeps
6.

5) Additional information

The NEOMAT-T motors recognise other ERGO, PLANO, NICEWAY and VOLO S RADIO series transmitters (see chapter 5.1 "Available trans-
mitters").
A particular command can also be associated to each transmitter button by means of a specific memorization procedure (see chapter 5.2
"Transmitter programming in Mode I and Mode II").
Warning: use transmitters that have been memorised in Mode 1 only for programming.
5.1) Available transmitters
Table A15 indicates the transmitters that can be used with the relat-
ed coding.
Table "A15"
Transmitters
ERGO1 - ERGO4 - ERGO6
PLANO1 - PLANO4 - PLANO6 - PLANO TIME
VOLO S RADIO
NICEWAY (the whole series)
FLO1R - FLO2R - FLO4R
VERY VR
5.1) Memorizing the transmitters in Mode I and Mode II
Tables "A1" and "A2" describe the memorization of the transmitters in "Mode I" where a specific command is assigned to each button: but-
ton ▲ (1) = "Up"; button ■ (2) = "Stop"; button ▼ (3) = "Down".
The transmitters can also be memorized on "Mode II", which allows greater flexibility in the use of the transmitter buttons. Transmitters can
be memorized both in Mode I and Mode II on the same NEOMAT-T motor.
5.2.1) Mode I
The command associated to the transmitter buttons is fixed in Mode I: button ▲
(1) = "Up"; button ■ (2) = "Stop"; button ▼ (3) = "Down", another button 4 com-
mands the "Stop".
A single memorization phase is performed in Mode I for each transmitter and a sin-
gle section is occupied in the memory. It is not important which button is pushed
when memorizing in Mode I.
Memorizing and deleting the transmitters in Mode I (see Tables A1 and A2).
10
ERGO PLANO
FLO4R VERY
Mode I
Button
Button ▲ or 1
Button ■ or 2
Button ▼ or 3
Button 4
Example
PP
5s
NICEWAY VOLO S RADIO
Command
Up
Stop
Down
Stop