Additional Information; Memory Deletion - Nice Neomat T Instrucciones Y Advertencias Para La Instalación Y El Uso

04. Confirm the position by pressing buttons ▼ and ▲ of the
transmitter together within 5 seconds until 3 beeps are
heard. At this point the awning will automatically move to
position "0".
Note: if the programming described in point 4 is not confirmed the modifications are
aborted and the previous programming is maintained. If after having programmed this
function you wish to eliminate it, the procedure in table A14 must be followed, omitting
step 3 which would modify position "1".
4.3.11 - Modifying position "1"
Follow the procedure indicated in table "A13" to modify position "1":
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A13" - Modifying position "1"
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down button ■ of a previously memorized
5s...
transmitter until you hear a beep (after about 5 seconds).
02. Press and hold buttons ■ ▼ for another 5 seconds until
5s...
2 rapid beeps are heard. At this point the awning auto-
matically moves to the position "1".
03. Use buttons ▼ and ▲ within 5 seconds to reposition the
awning in the new position to be programmed.
04. Confirm the position by pressing buttons ■ ▼ of the
transmitter together within 5 seconds until 3 beeps are
heard and a short up and down movement is performed.
Note: if the programming described in point 4 is not confirmed the modifications are
aborted and the previous programming is maintained.
By modifying position "1" the "FRT" and "FTC" functions are cancelled.

4.4 - Memory deletion

If you need to delete all the transmitter and the programmed operations, carry out the
procedure shown in table A14.
The memory can be deleted:
• with a non-memorized transmitter starting from point A.
• with a previously memorized transmitter starting from point No. 1.
The following can be deleted:
• only the memorized transmitters, finishing at point No. 4
• all data (transmitters, sensor level, TTBUS address, etc.), completing the procedure
until point 6.
8 – English
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A14" - Memory deletion
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
A. Switch the motor off, activate the Step-by-Step input (by
P.P.
connecting the White cable with the White/Black one)
and keep it active until the end of the procedure.
B. Power the motor and wait for the initial beeps.
01. Press and hold down button ■ on a transmitter (about 5
5s...
seconds) until you hear a beep; then release it.
02. Hold down the ▲ button on the transmitter until you hear
3 beeps; release the ▲ button exactly during the third
beep.
03. Hold down button ■ on the transmitter until you hear 3
beeps; release button ■ exactly during the third beep.
04. Hold down the ▼ button on the transmitter until you hear
3 beeps; release the ▼ button exactly during the third
beep.
05. To cancel everything: press both ▲ and ▼ within 2 sec-
onds.
06. Cancellation is confirmed by releasing buttons ▲ and ▼
on the first of the 5 beeps.
5

Additional information

The NEOMAT-T motors recognise other ERGO, PLANO, NICEWAY, VOLO S RADIO and
NEMO series transmitters (see chapter 5.1 "Available transmitters").
A particular command can also be associated to each transmitter button by means of a
specific memorization procedure (see chapter 5.2 "Transmitter programming in Mode I
and Mode II").
Warning: use transmitters that have been memorised in Mode I only for program-
ming.