Spraying Precautions - Campbell Hausfeld WL6100 Serie Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Operating Instructions
General Safety
2. Follow all local electrical and safety
codes, as well as in the U.S.A.,
National Electrical Codes (NEC) and
Occupational Safety and Health Act
(OSHA).
3. Only persons well acquainted with
these rules of safe operation should
be allowed to use the compressor.
4. Keep visitors away and NEVER allow
children in the work area.
5. Wear safety glasses and
use hearing protection
when operating the pump
or unit.
6. Do not stand on or use the pump or
unit as a handhold.
7. Before each use, inspect compressed
air system and electrical components
for signs of damage, deterioration,
weakness or leakage. Repair or
replace defective items before using.
8. Check all fasteners at frequent
intervals for proper tightness.
Motors, electrical equipment
and controls can cause
electrical arcs that will ignite
a flammable gas or vapor. Never
operate or repair in or near a
flammable gas or vapor. Never store
flammable liquids or gases in the
vicinity of the compressor.
Compressor parts may be hot
even if the unit is stopped.
9. Keep fingers away from a running
compressor; fast moving and hot
parts will cause injury and/or burns.
10. If the equipment should start to
abnormally vibrate, STOP the
engine/motor and check
immediately for the cause. Vibration
is generally a warning of trouble.
11. To reduce fire hazard, keep
engine/motor exterior free of oil,
solvent, or excessive grease.
or attempt to adjust safety valve. Keep
safety valve free from paint and other
accumulations.
www.chpower.com
(Con't)
Never attempt to repair or
modify a tank! Welding,
drilling or any other
modification will weaken the tank
resulting in damage from rupture or
explosion. Always replace worn or
damaged tanks.
Drain liquid from tank daily.
12. Tanks rust from moisture build-up,
which weakens the tank. Make sure
to drain tank daily and inspect
periodically for unsafe conditions
such as rust formation and corrosion.
13. Fast moving air will stir up dust and
debris which may be harmful.
Release air slowly when draining
moisture or depressurizing the
compressor system.

SPRAYING PRECAUTIONS

Do not spray flammable
materials in vicinity of open
flame or near ignition
sources including the compressor unit.
14. Do not smoke when spraying paint,
insecticides, or other flammable
substances.
15. Use a face mask/
respirator when spraying
and spray in a well
ventilated area to
prevent health and fire hazards.
16. Do not direct paint or other sprayed
material at the compressor. Locate
compressor as far away from the
spraying area as possible to
minimize overspray accumulation
on the compressor.
17. When spraying or cleaning with
solvents or toxic chemicals, follow
the instructions provided by the
chemical manufacturer.
Never
Risk of electrical shock. Turn
remove
off and unplug before
servicing. Service should be performed
by an authorized service center.
Assembly
HANDLE ASSEMBLY (Figure 1)
1. Place ends of handle into handle inserts
2. Assemble four (4) screws (from parts
handle to lift the unit completely off
the ground. Only use the handle to lift
one end so the wheels may be used to
move the unit.
WHEEL ASSEMBLY (Figure 2)
Figure 2 - Wheel Assembly
Wheel assembly kit includes:
- 2 wheels*
- 2 axle bolts*
- 2 lock washers*
- 2 nuts*
The items marked with an asterisk (*)
were shipped loose with the unit.
1. Wheel has an offset hub. With offset
2
Figure 1 - Handle Assembly
on sides of tank.
package) through holes in handle.
Nut
Lock washer
Wheel
Axle bolt
hub facing axle iron, assemble axle
bolt through holes in wheel and axle
iron.
Screws
Never use
the

Publicidad

Tabla de contenido
loading

Tabla de contenido