How To Start Your Watch; Water And Shock Resistance; Indiglo ® Night-Light; Analog/Digital Model - Timex 931-095000 1.30.19 Guia Del Usuario

HOW TO START YOUR WATCH

To start your watch remove the plastic guard from under the crown, then press
the crown in against the case... The second hand will begin advancing in one-
second intervals...
Some deep-depth water-resistant watches require the setting crown to be
screwed in to secure water-resistance. If your watch case has a protrusion with
screw threads, the crown must be screwed in after setting the watch.
To screw in, push the crown firmly against the threaded protrusion and hold
in while turning the crown clockwise. Continue to screw in the crown until it is
tight. You will need to unscrew the crown (counter-clockwise) before pulling it
out the next time you want to set your watch.

WATER AND SHOCK RESISTANCE

If your watch is water-resistant, meter marking (WR_M) is indicated.
Water-Resistance Depth
30m/98ft
50m/164ft
100m/328ft
200m/656ft
*pounds per square inch absolute
WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY
BUTTONS OR PULL OUT THE CROWN UNDER WATER UNLESS YOUR
WATCH IS INDICATED AS 200 METER WATER-RESISTANT.
1. Watch is water-resistant only as long as crystal, crown and case remain
intact...
2... Watch is not a diver watch and should not be used for diving...
3... Rinse watch with fresh water after exposure to salt water...
4. Shock-resistance will be indicated on the watch face or caseback. Watches
are designed to pass ISO test for shock-resistance. However, care should be
taken to avoid damaging the crystal.
INDIGLO NIGHT-LIGHT
®
Press button to activate light. Electroluminescent technology used in the
INDIGLO night-light illuminates entire watch face at night and in low light
®
conditions...

ANALOG/DIGITAL MODEL

4-PUSHER ANALOG/DIGITAL MODEL WITH INDIGLO
NIGHT-MODE FEATURE
®
PUSHER
"B"
PUSHER
"A"
TO USE INDIGLO NIGHT-LIGHT
®
1. PRESS pusher "B" to illuminate the entire dial (Both analog and digital).
TO USE NIGHT-MODE FEATURE
®
1... PRESS and HOLD INDIGLO
®
2... Pressing any pusher will cause the INDIGLO
stay on for 3 seconds.
3... NIGHT-MODE feature will last for 8 hours...
®
4... To deactivate NIGHT-MODE
®
for 3 seconds...
ANALOG TIME
TO SET ANALOG TIME
1... PULL the crown out to the "B" position...
2. TURN the crown either way to the correct time.
3... PUSH in the crown to the "A" position...
p.s.i.a. * Water pressure Below Surface
60
86
160
284
NIGHT-LIGHT &
®
PUSHER
"C"
A B
CROWN
POSITION
PUSHER
"D"
Button for 3 seconds until you hear a beep.
night-light to illuminate and
®
feature PRESS and HOLD INDIGLO
DIGITAL DISPLAY
1. The Digital display changes to each function every time you PRESS pusher
"A" (As illustrated below):
TIME / CALENDAR
DAILY ALARM
COUNTDOWN TIMER
CHRONOGRAPH
DUAL TIME
START
TO SET TIME / CALENDAR
1. PRESS pusher "A" to bring up TIME / CALENDAR display.
2. PRESS and HOLD pusher "D". HOLD will display until hours flash.
3... PRESS pusher "C" to advance hours...
4. PRESS pusher "A" and "C" as above to adjust minutes, reset seconds to
"00", month, date, year and 12/24 hour format.
5... PRESS pusher "D" to complete setting...
NOTE: PRESS and HOLD pusher "C" for 2 seconds in setting mode, to
activate fast advance...
View or select the TIME or CALENDAR to appear in your digital display.
1... PRESS pusher "C" to view the CALENDAR for 2 seconds...
2... PRESS and HOLD pusher "C" for 3 seconds until the watch beeps and
changes the display to CALENDAR.
3. To view or change the display to TIME, repeat the steps above.
NOTE:
• "A" or "P" will appear when the 12-Hour format is selected...
• Set this time to coordinate with the Analog time or another time zone...
TO SET DAILY ALARM
WILL
APPEAR
FOR 3
SECONDS
1. PRESS pusher "A" to bring up DAILY ALARM display: "ALARM" will appear
for 3 seconds followed by the current alarm setting time and time zone. The
ALARM mode symbol "AL" and the applicable time zone symbol "T1" or "T2"
alternate to give complete information...
2. PRESS pusher "D" to let time zone flash.
3... PRESS pusher "C" to select time zone...
4. PRESS pusher "A" to let hour flash.
5... PRESS pusher "C" to advance hour...
6... PRESS pusher "A" and "C" as above to adjust the minutes...
7... PRESS pusher "D" to complete setting...
8. Alarm is automatically activated after setting.
Button
® ®
NOTE: PRESS and HOLD pusher "C" for 2 seconds in setting mode, to
activate fast advance...
NOTE:
• When the alarm sounds, it will beep for 20 seconds.
• To stop the alarm beep, PRESS any pusher.
2
TIME/ DAILY
CALENDAR ALARM
Press and release MODE Press and release MODE
button once. button once.
DUAL TIME CHRONOGRAPH
HOUR MINUTE SECOND MONTH
HOUR MINUTE SECOND MONTH
FOLLOWED BY
THE CURRENT
ALARM SETTING
TIME AND TIME
ZONE.
C
931-09500
ENGLISH
COUNTDOW N
TIMER
Press and release MODE
button once.
DATE DAY
CALENDAR
DATE DAY
CALENDAR
is displayed.