Electric Installation; Technical Data - Vetus Napoleon Manual De Manejo Y Instrucciones De Instalación

Electric installation

Check whether the voltage, as mentioned on the engine plate,
is in accordance with the ship's power supply.
Battery
Install a starter battery with a capacity of approx. 1 Ah - 12V.
(e.g. a Vetus maintenance free marine battery of 1 Ah.)
For 2V, 2 starter batteries of approx. 90 Ah - 12V in series
connections. (e.g. 2 pcs. Vetus maintenance free marine bat-
teries 90 Ah).
Position the batteries as closely as possible to the anchor
windlass; the main circuit wires can be kept short and which
causes the voltage drop to be low.
The place in which the batteries are installed should be dry
and
well ventilated.
Main circuit wires
The minimum cross section is 25 mm
For 2 V minimum 10-mm 2 (AWG 8).
The voltage drop between the battery and the anchor windlass
should not exceed 5 percent of the supply voltage.
Consult the table on page 27 when choosing the proper cross
section.
A main switch and a fuse are to be inserted into the plus cable.
A Vetus battery switch is excellently suited for the job. The
fuse protects the anchor windlass against overload as well as
the ship's supply system against short circuits.
A recommended fuse is the Vetus 'slow blow' fuse.
- 12 V anchor windlass: 80 A
- 2 V anchor windlass: 0 A
- Fuse holder
ZEHC100)
Solenoid switch
The anchor windlass motor is already fitted with 2 built-in sole-
noid switches (relay).
Connect the anchor windlass motor as shown in the diagram
on page 26.
Connect the motor as indicated in the diagram on page 26.
Note!
The two motor relays must never be switched on at the same
time. There is a danger of this occurring when two separate
switches (e.g. AFSTFR/ AFSTFG) are used for hauling in and
letting go. If that is the case, 2 extra relays should be installed.
See diagram.
Remote control
All Vetus remote controls for anchor windlasses can be used in
combination with the Napoleon anchor windlass.
For example: AWPANEL, RC2, AFSTFR, AFSTFG, RECON.
Vetus chain counters are specially designed for use in combina-
tion with the Napoleon anchor windlass:
CCM : Combined control panel/ chain counter
CCFB : Chain counter
See the separate manual.
Electric anchor windlass 'Napoleon'
2 (AWG ).
(Vetus art. code: ZE080)
(Vetus art. code: ZE00)
(Vetus art. code:

Technical data

Electric motor
Type : Direct current series motor
Voltage : 12 V DC
Rated current : 70 - 110 A
Rated output : Nominal 1000 W; Maximum 1850 W
Rating : S2 - 11 min.
Protection : IP66
Transmission
Gears : worm wheel, ratio: 52:1
Gipsy 1 : For chain 8 mm DIN766, 8 mm ISO565,
5/16" HT, 5/16" BBB;
for rope 1 - 16 mm
Gipsy 2 : For chain 10 mm DIN766, /8" BBB
Gipsy 3 : For chain 10 mm ISO565, /8" HT
Lifting power : nominal 500 N (780 lbf)
max. 9500 N (2110 lbf)
Haulage speed : 18 - 2 m/min, dependent on the load
'Free fall' speed : up to 5 m/min
Weight : 21 kg (6 lbs)
We can also supply:
Anchor chain
Art. code: Article description:
CHAIN08SS Anchor chain 8 mm DIN 766, per metre
(stainless steel)
CHAIN10SS Anchor chain 10 mm DIN 766, per metre
(stainless steel)
CHAIN08.. Anchor chain 8 mm DIN 766
(calibrated and galvanised)
CHAIN10.. Anchor chain 10 mm DIN 766
(calibrated and galvanised)
Bow rollers
Art. code: Article description:
ASTERIX Bow roller type Asterix, suitable for rope and
chain up to 8 mm (5/16")
OBELIX Bow roller type Obelix, suitable for rope and
chain up to 1 mm (1/2")
POLLY Bow roller type Polly, suitable for rope and
chain up to 8 mm (5/16")
FRANCIS Bow roller type Francis, suitable for rope
and chain up to 8 mm (5/16")
ED Bow roller type Ed, suitable for rope and
chain up to 1 mm (1/2")
ENGLISH
2 V DC
0 - 60 A
9
060121.02