EINHELL BT-MC 355 Manual De Instrucciones Original página 14

Anleitung_BT_MC_355_SPK7__ 19.10.12 10:38 Seite 14
GB
a switch that cannot be turned on and off.
18. Direction of operation: Make sure that the
direction arrow points toward the workpiece.
19. Never leave an electric tool unattended when it is
running. Always switch off your electric tool
before leaving it. Wait until the tool stops moving
completely.
20. Connect your electric tool to earth. An electric
tool with a PE conductor may only be connected
to a matching socket-outlet.
21. Make allowance for ambient conditions. Do not
expose electric tools to rain. Never use electric
tools in damp or wet locations. Provide good
lighting. Do not use electric tools near flammable
liquids or gases.
22. Guard against electric shock. Avoid body contact
with earthed components.
23. Keep your electric tools in a safe place. When
equipment is not being used it should be kept in
a dry, closed place out of childrenʼs reach.
24. Connect up a dust extraction system. If there are
provisions for connecting up a dust extraction
and collection system, make sure that such a
system is connected and in use.
25. Use the cable for its intended purpose only. Do
not use the cable to pull the plug out of the
socket-outlet. Protect cables from heat, oil and
sharp edges.
26. Avoid abnormal working postures. Make sure
you stand squarely and keep your balance at all
times.
27. Avoid unintentional starting. Make sure that the
switch is OFF when inserting the plug in the
socket-outlet.
28. When working outdoors, use only extension
cables that are approved for outdoor use and
which are marked accordingly.
29. Be alert at all times. Concentrate on what you
are doing. Use common sense. Never use the
electric tool when you are distracted.
30. CAUTION! The use of mounted attachments and
accessories other than those intended may put
you at risk of injury.
31. Have repairs carried out only by a qualified
electrician. This electric tool complies with the
pertinent safety regulations. Repairs have to be
carried out by a qualified electrician using
original replacement parts. If not, the user may
suffer an accident.
32. Do not lose these safety regulations.
14
Additional safety rules for cutting-off
machines
1. CAUTION! Never use your cutting-off machine
unless it is fully assembled and installed as
described in this manual.
2. If you are not acquainted with the use of a
cutting-off machine, get advice from a
supervisor, trainer or other qualified person.
3. Wear safety goggles, a visor, a breathing mask,
an apron, safety shoes, long tight sleeves and
gloves.
4. Use only recommended, reinforced cutting-off
wheels.
5. Securely tighten the shaft screw and all clamps
before beginning your work.
6. Make sure that the shaft lock is released before
starting.
7. Always leave the safety devices in position and
make sure that they are in good working order.
8. Keep your hands away from the cutting-off
wheel.
9. Secure the workpiece carefully. It has to be
securely clamped in a straight position in order to
prevent it from moving and skewing while the cut
is being made.
10. Never cut free-handed.
11. Never reach behind or near the cutting-off wheel.
12. Make sure that the cutting-off wheel stops
completely before you remove the workpiece,
clamp in a new workpiece, or adjust the angle.
13. Make sure that there are no foreign bodies on
the cutting-off wheel and flange.
14. When you fit a cutting-off wheel, take care to
tighten the shaft screw just enough to hold the
wheel in place and prevent it from spinning.
Overtightening the shaft screw may damage the
cutting-off wheel or cause it to break off the
wheel flange.
15. Use only recommended cutting-off wheels that
are suitable for 3800/min or higher and are
marked accordingly.
16. Always check the cutting-off wheel for cracks or
other signs of damage. Replace cracked or
damaged cutting-off wheels immediately.
17. Use only the cutting-off wheel flanges specified
for your machine.
18. Before you switch on, make sure that the cutting-
off wheel does not touch the machine.
19. Allow the motor to reach top speed before you
begin to cut.
20. After you have switched on, lower the cutting-off
wheel slowly until it comes into contact with the
workpiece. Then carry out a smooth cut. Avoid
causing the cutting-off wheel to jump or chatter.