Makita DLS600 Manual De Instrucciones página 27

NOTICE:
When turning the turn base, be sure to
raise the handle fully.
Adjusting the bevel angle
To adjust the
turn the lever
the tool downward. ► Fig.21:
rear of
1. Lever
To tilt the blade to the left, hold the handle and tilt the
saw head. Use the bevel scale and the pointer as a
guide.
Then turn the
firmly to secure
head. ►
Fig.22: 1. Pointer 2. Bevel scale
To tilt the blade to the right, hold the handle and tilt the
saw head to the left slightly, and push the release
button. With the release button pressed, tilt the saw
blade to the right. Turn
upward firmly to
head. ►
saw Fig.23:
CAUTION:
After changing the bevel angle,
always secure the saw head by turning the lever
upward firmly.
NOTICE:
When tilting the saw blade, be sure the
handle is fully raised.
NOTICE:
When changing bevel angles, be sure
to position the kerf boards appropriately as
explained in the "Positioning kerf boards"
section.
Setting 46° bevel angle
1. Loosen the lever and tilt the blade to the left
or right fully.
►
Fig.24: 1. Lever
2. To tilt the blade to the left, hold the handle
and tilt the saw head to the right slightly, and then move
the release lever to the direction of the arrow. The bevel
angle can be
45°
to
tilting the
moving the release lever.
To tilt the blade to the right, hold the handle and tilt the
saw head to the left slightly, and then move the release
lever to the direction of the arrow. The bevel angle can
be adjusted between
46°
by tilting
head while moving the release lever.
►
Fig.25: 1. Lever 2. Release lever
3. Turn the
firmly to
saw head.
bevel angle,
at the
lever upward
the saw
the lever
secure the
1. Release button
adjusted between
46°
by
saw head while
45°
to
the saw
lever upward
secure the
27 ENGLISH
Adjusting the lever position
If the lever does not provide full tightening in course of
time, change the position of the lever. The lever can be
repositioned at every 30° angle.
Loosen and remove the screw that secures the lever.
Remove the lever and install it again so that it points
slightly above the horizontal. Then, tighten the lever
with the screw
►
Fig.26: 1. Lever 2. Screw
Switch action
WARNING:
Before installing the battery
cartridge on the tool, always check to see that the
switch trigger actuates properly and returns to the
"OFF" position when released. Operating a tool with
a switch that does not actuate properly can lead to
loss
serious
WARNING:
NEVER use tool without a fully
operative switch trigger. Any tool with an inoperative
switch is HIGHLY DANGEROUS and must be repaired
before further usage or serious personal injury
may
WARNING:
For your safety, this tool is equipped
with a lock-off button which prevents the tool from
unintended starting. NEVER use the tool if it runs
when you simply pull the switch trigger without
pressing the lock-off button. A switch in need of
repair may result in unintentional operation and
serious personal
to
center for proper repairs BEFORE further
usage.
WARNING:
NEVER defeat the lock-off button
by taping down or some other means. A switch with
a negated lock-off button may result in unintentional
operation and
NOTICE:
Do not pull the switch trigger hard
without pressing in the lock-off button. This can
cause switch breakage.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
►
Fig.27: 1. Lock-off button 2. Hole for
padlock
3. Switch trigger
firmly.
of control and
personal injury.
occur.
injury. Return tool
a Makita service
serious personal injury.