Makita DLS600 Manual De Instrucciones página 29

insufficient tightening of the hex socket
bolt. This could cause an
To remove the blade, perform the following steps:
1. Release the stopper pin, and then lock the
handle in the raised position by pushing in the stopper
pin. ►
Fig.33: 1. Stopper pin
2. Use the hex wrench to loosen the hex
socket bolt holding the center cover by turning it
counterclockwise.
Then, raise the blade guard and center cover.
►
Fig.34: 1. Center cover 2. Hex socket bolt
3. Hex wrench 4. Blade guard
3. Press the shaft lock to lock the spindle and
use the hex wrench to loosen the hex socket bolt
clockwise. Then remove the hex socket bolt of the
spindle, outer flange and
►
Fig.35: 1. Shaft lock 2. Hex socket bolt 3.
Outer flange
4. If the
is removed, install
on the
mounting part facing the blade. If the flange is
installed incorrectly the
will rub
machine.
►
Fig.36: 1.
2. Saw blade 3. Inner
4. Hex socket bolt (left-handed) 5. Spindle
6. Blade mounting part
To install the blade, perform the following steps:
1. Mount the
onto the
Make sure that the direction of the arrow on
the blade matches the direction of the arrow on the
blade case.
►
Fig.37: 1. Saw blade 2. Arrow
2. Install the
and hex
and then use the hex wrench to
tighten the hex socket bolt (left-handed) of the spindle
securely counterclockwise while pressing the shaft lock.
3. Return the blade guard and center cover to
its original position. Then tighten the hex socket bolt of
the center cover clockwise to secure the center cover.
4. Release the handle from the raised position
by pulling the stopper pin. Lower the handle to make
sure that the blade guard moves properly.
5. Make sure the shaft lock has released
spindle before making cut.
injury.
blade.
inner flange
it
spindle with its blade
flange
against the
Outer flange
flange
blade carefully
inner flange.
outer flange
socket bolt,
29 ENGLISH
For tool with the inner flange for
15.88 mm hole-diameter saw blade
Country specific
Mount the inner
its recessed side
onto the mounting shaft and then place saw blade
(with the ring
needed), outer flange
For tool without the ring
►
Fig.38: 1.
2. Saw blade 3. Inner
4. Hex socket bolt (left-handed) 5. Spindle
For tool with the ring
►
Fig.39: 1.
2. Saw blade 3. Inner
4. Hex socket bolt (left-handed) 5. Ring
6. Spindle
WARNING:
If the ring is needed to mount the
blade onto the spindle, always be sure that the
correct ring for the blade's arbor hole you intend
to use is installed between the inner and the outer
flanges. Use of the incorrect arbor hole ring may
result in the improper mounting of the blade causing
blade movement and severe vibration resulting in
possible loss of control during operation and in
serious personal
For tool with the inner flange for
other than 20 mm or 15.88 mm
holediameter saw blade
Country specific
The inner flange
certain diameter of
mounting part on one side of it and a different diameter
of blade mounting part on the other side. Choose a
correct side on
mounting part fits
saw blade hole perfectly.
►
Fig.40: 1.
2. Saw blade 3. Inner
4. Hex socket bolt (left-handed) 5. Spindle
6. Blade mounting part
CAUTION:
Make sure that the blade mounting
part "a" on the inner flange that is positioned
outside fits into the saw blade hole "a" perfectly.
Mounting the blade on the wrong side can result in the
dangerous vibration.
Dust bag
The use of the dust bag makes cutting operations
cleaner and dust collection easier. To
the dust bag,
onto the dust
dust bag is about half full, remove the dust bag from the
tool and pull the fastener out. Empty the dust bag of its
flange with
facing outward
attached if
and hex bolt.
Outer flange
flange
Outer flange
flange
injury.
has a
a blade
which blade
into the
Outer flange
flange
attach
fit it
nozzle. When the