Troubleshooting Guide - DeWalt DWS713 Manual De Instrucciones

ENGlIsH
DO NOT use lubricants or cleaners (particularly spray or aerosol) in the vicinity of the plastic
guard. The polycarbonate material used in the guard is subject to attack by certain chemicals.
1. All bearings are sealed. They are lubricated for life and need no further maintenance.
2. Periodically clean all dust and wood chips from around AND UNDER the base and the
rotary table. Even though slots are provided to allow debris to pass through, some dust
will accumulate.
3. The brushes are designed to give you several years of use. To replace the brushes return the
tool to the nearest service center for repair. A list of service center locations is packed with
your tool.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a
week. To minimize the risk of eye injury, always wear approved eye protection when
performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Accessories

WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
e
Recommended accessories for use with your tool are available at extra cost from your local dealer
or authorized service center.
Optional Accessories
The following accessories, designed for your saw, may be helpful. Use care in selecting and
using accessories.
Clamp: DW7090
Used for firmly clamping workpiece to the saw fence for precision cutting.
Dust Bag: DW7053
Included with some models
Equipped with a zipper for easy emptying, the dust bag will capture the majority of the sawdust
produced (not shown).
Crown Molding Fence: DW7084
Used for precision cutting of crown molding.
Miter saw Replacement Kerf plate: DW7055
This durable plastic uncut plate limits blade tear out.
Miter saw stands: DWX723, DWX724, DWX725B, DWX726
Provides stable and accurate work platform for miter saws.
TROUBLE!
Saw will not start
Saw makes unsatisfactory cuts
Blade does not come up to speed
Machine vibrates excessively
Does not make accurate miter cuts
Material pinches blade
38
WALT, have not been tested
e

Troubleshooting Guide

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
WHAT'S WRONG?
Saw not plugged in
Fuse blown or circuit breaker tripped
Cord damaged
Brushes worn out
Dull blade
Blade mounted backwards
Gum or pitch on blade
Incorrect blade for work being done
Extension cord too light or too long
Low house current
Saw not mounted securely to stand or work bench
Stand or bench on uneven floor
Damaged saw blade
Miter scale not adjusted correctly
Blade is not square to fence
Blade is not perpendicular to table
Workpiece moving
Cutting bowed material
saw Blades
ALWAYS USE 10" (254 mm) SAW BLADES WITH 5/8" (16 mm) ARBOR HOLES. SPEED RATING
MUST BE AT LEAST 5500 RPM. Never use a smaller diameter blade. It will not be guarded properly.
Use crosscut blades only! Do not use blades designed for ripping, combination blades or blades
with hook angles in excess of 7 degrees.
BLADE DESCRIPTIONS
APPLICATION
Construction Saw Blades (thin kerf with anti-stick rim)
General Purpose
Fine Crosscuts
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts
Non-ferrous metals
NOTE: For cutting non-ferrous metals, use only saw blades with TCG teeth designed for this purpose.
Repairs
The charger and battery pack are not serviceable.

WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (including brush inspection and replacement) should be performed by a
D WALT factory service center or a D
e
replacement parts.
Protecting the Environment
Separate collection. Products and batteries marked with this symbol must not be
disposed of with normal household waste.
Products and batteries contain materials that can be recovered or recycled reducing the demand
for raw materials. Please recycle electrical products and batteries according to local provisions.
SPECIFICATIONS
DWS713-B3
Voltage 120 V~
Frequency 60 Hz
Power 2200 W
Speed 5000/min (rpm)
WHAT TO DO
Plug in saw.
Replace fuse or reset circuit breaker.
Have cord replaced by authorized service center.
Have brushes replaced by authorized service center.
Replace blade. Refer to Changing or Installing a New Saw Blade.
Turn blade around. Refer to Changing or Installing a New Saw Blade.
Remove blade and clean with turpentine and coarse steel wool or household oven cleaner.
Change the blade type. Refer to Saw Blades under Accessories.
Replace with adequate size cord. Refer to Additional Saftey Rules for Miter Saws.
Contact your electric company.
Tighten all mounting hardware. Refer to Bench Mounting.
Reposition on flat level surface. Refer to Familiarization.
Replace blade. Refer to Changing or Installing a New Saw Blade.
Check and adjust. Refer to Miter Scale Adjustment under Assembly and Adjustments.
Check and adjust. Refer to Miter Scale Adjustment under Assembly and Adjustments.
Check and adjust fence. Refer to Bevel Square to Table under Assembly and Adjustments.
Clamp workpiece securely to fence or glue 120 grit sandpaper to fence with rubber cement.
Refer to Bowed Material under Special Cuts.
DIAMETER TEETH
10" (254 mm) 40
10" (254 mm) 60
10" (254 mm) 80
10" (254 mm) 80
WALT authorized service center. Always use identical
e
DWS713-AR DWS713-B2 DWS713-BR
220 V~ 220 V~
50 Hz 50–60 Hz
2200 W 2200 W
5000/min (rpm) 5000/min (rpm) 5000/min (rpm)
127 V~
60 Hz
2200 W