Specific Safety Rules; On-Off Switch - Black+Decker WP600K Manual De Instrucciones

14 • ENGLISH
h. Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by
various operations. The dust mask or respirator
must be capable of filtrating particles generated by
your operation. Prolonged exposure to high intensity
noise may cause hearing loss.
i. Keep bystanders a safe distance away from
work area. Anyone entering the work area must
wear personal protective equipment. Fragments
of workpiece or of a broken accessory may fly away
and cause injury beyond immediate area of operation.
j. Hold the power tool by insulated gripping
surfaces only, when performing an operation
where the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory contacting
a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an
electric shock.
k. Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory.
l. Never lay the power tool down until the accessory
has come to a complete stop. The spinning
accessory may grab the surface and pull the power
tool out of your control.
m. Do not run the power tool while carrying it at your
side. Accidental contact with the spinning accessory
could snag your clothing, pulling the accessory into
your body.
n. Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
o. Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
p. Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
result in electrocution or shock.

SPECIFIC SAFETY RULES

f Accessories must be rated for at least the speed
ecommended on the tool warning label. Wheels
and other accessories running over rated speed can
fly apart and cause injury.
f Hold tool by insulated gripping surfaces when
performing an operation where the polishing
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
f Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing
and wash exposed areas with soap and water.
Allowing dust to get into your mouth, eyes, or lay on
the skin may promote absorption of harmful chemicals.
f Always wear eye protection.
f Be sure bonnet is snugly installed on pad.
f Keep hands and fingers away from rotating bonnet.
f Before turning the switch to the ON position, be sure
the pad is free to revolve harmlessly.
f Inspect the bonnet frequently for wear, dirt or
imbedded debris.
Caution! Do not allow the power cord to contact the
rotating bonnet as it may become quickly tangled around
it. If this occurs, turn tool OFF and unplug the power
cord before attempting to untangle the cord. If the cord is
damaged, have it repaired or replaced at your local tool
repair station:
f Never use a damaged or torn bonnet.
f Wear proper clothing, short sleeves, nothing loose or
bulky, such as shop coat, etc.
f Do not turn tool on unless the polishing bonnet is
against surface being polished.
f Be extremely careful when polishing around sharp or
protruding objects on the car body.
Caution! Do not use abrasive or rubbing compounds.
The abrasive nature of these products can damage
painted surfaces.
Caution! Wear appropriate hearing protection during
use. Under some conditions and duration of use, noise
from this product may contribute to hearing loss.
INSTALLING THE SIDE HANDLE
The side handle should always be used during operation.
Screw the handle into the top, left or right of the grinder
housing .It´s determined by your need.

ON-OFF SWITCH

1. Pressing trigger (7) while moving trigger lock (6)
forward to turn "ON" the tool. And moving trigger lock
forward again, the trigger will locked.
2. Press trigger (7) again to turn the tool "OFF".
MOUNTING AND DISMOUNTING THE WOOL
BONNET
1. Insert the washer nut through the rubber pad and
thread it onto the spindle.
2. While holding the spindle with the stop pin (10).
Turn the washer nut clock wise with accessory
wrench to screw it onto the spindle. Ensure that the
washer nut is thoroughly tightened by using wrench.
3. Wrap the rubber pad with the hood of the wool bonnet
and firmly secure it by tightening and trying its draw