Establishing The Mains Connection (08); Starting And Stopping The Motor (09); Attaching And Removing The Grass Collector (10); Moving The Appliance On The Grass (11) - AL-KO COMBI-CARE 36 E Comfort Traducción Del Manual Original De Instrucciones

GB
1. Turn the adjuster wheel (07/1) to HIGH, i.e.
level 1 on the working depth indicator (07/2).
The blade system is raised to the maximum.
2. Checking the working depth:
■
Start the appliance (see chapter 6.5

"Starting and stopping the motor (09)",

page 20).
■
Move a little way onto the grass and
check the result. If the grass is too short
or irregularly scarified, the blade system
must be lowered.
3. Stop the appliance and wait until the blade
system has stopped.
4. Turn the adjuster wheel (07/1) a little towards
LOW, i.e. levels 2 to 5. The blade system is
lowered.
5. Repeat the previous steps until the grass is
uniformly scarified.
6.4

Establishing the mains connection (08)

1. Firmly plug the socket (08/1) of the mains
cable into the plug (08/2) on the motor
switch.
2. Clamp the mains cable (08/3) in the cable
strain relief (08/4) (pos. a, pos. b) so it cannot
be pulled off the motor switch.
6.5 Starting and stopping the motor (09)
IMPORTANT!
Danger of damage to the appliance
The motor and blade system can be
damaged by consecutively switching on
and off briefly several times.
■
Only switch the motor on when the
blade system has stopped.
Starting the motor
1. Press and hold the safety push switch (09/1)
(pos. a).
2. Pull the motor switch bracket (09/2) to the
handlebar (09/3) (pos. b). The motor and
blade system are started.
3. Release the safety push switch (09/1) and
hold the motor switch bracket (09/2).
NOTE
The motor switch bracket does not lock in
place. Hold it tight against the handlebar
during the entire working period.
20
Stopping the motor
1. Release the motor switch bracket (09/2). It
automatically returns to the initial position
(pos. c).
The motor stops immediately. The blade system
keeps running until it stops.
CAUTION!
Danger of lacerations
There is a danger of lacerations when
reaching into the blade system while it is
running on.
■
Wait until the blade system has
stopped.
6.6 Attaching and removing the grass
collector (10)
The appliance can be operated with and without
grass collector.
Attaching the grass collector
1. Raise the impact flap (10/1) (pos. a).
2. Attach the grass collector (10/2) in the hold-
ers (pos. b) from behind.
3. Release the impact flap.
Removing and emptying the grass collector
1. Stop the appliance and wait until the blade
system has stopped.
2. Raise the impact flap (10/1).
3. Lift the grass collector (10/2) out of the hold-
ers and take off to the rear.
4. Empty the grass collector.
5. Attach the grass collector (see above).
6.7 Moving the appliance on the grass (11)
Guide the appliance (11/1) over the grass (as
shown in the image) in such a way to avoid dam-
aging the mains cable (11/2). Heed the safety in-
structions (see chapter 3 "Safety instructions",
page 18).
■
Watch out for objects in the grass and re-
move them from the working area.
■
Guide the mains cable by hand.
■
Only control the appliance by the handlebar.
■
Move the appliance at walking speed.
■
Always move the appliance across the slope.
■
If the motor suddenly stops: The motor circuit
breaker has triggered due to an overload.
Wait a few minutes and then attempt to start
the motor again.
Operation
COMBI-CARE 36 E comfort