Silverline 613578 Manual Del Usuario página 7

613578
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating part
of the power tool may result in personal injury
e) Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in unexpected
situations
f) Dress properly. Do not wear loose clothing or jewellery. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts
g) If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and
properly used. Use of dust collection can reduce dust-related
hazards
Power Tool Use & Care
a) Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better and
safer at the rate for which it was designed
b) Do not use the power tool if the switch does not turn it on and
off. Any power tool that cannot be controlled with the switch is
dangerous and must be repaired
c) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool
accidentally
d) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users
e) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tool's operation. If damaged, have the
power tool repaired before use. Many accidents are caused by
poorly maintained power tools
f) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account the
working conditions and the work to be performed. Use of
the power tool for operations different from those intended could
result in a hazardous situation
Service
a) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that the
safety of the power tool is maintained
Cutting Tool Safety
WARNING. Before connecting a tool to a power source (mains switch
power point receptacle, outlet, etc.) be sure that the voltage supply
is the same as that specified on the nameplate of the tool. A power
source with a voltage greater than that specified for the tool can result
in serious injury to the user, and damage to the tool. If in doubt, do
not plug in the tool. Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
Use the correct cutting tool
• Ensure the cutting tool is suitable for the job. Do not assume a tool is
suitable without checking the product literature before use
Protect your eyes
• Always wear appropriate eye protection when using cutting tools
• Spectacles are not designed to offer any protection when using this
product; normal lenses are not impact resistant and could shatter
Protect your hearing
• Always wear suitable hearing protection when tool noise exceeds 85dB
Protect your breathing
• Ensure that yourself, and others around you, wear suitable dust masks
Be aware of others around you
• It is the responsibility of the user to ensure that other people in the vicinity
of the work area are not exposed to dangerous noise or dust and are also
provided with suitable protective equipment
Hidden objects
• Inspect the workpiece and remove all nails and other embedded objects
before cutting
• Do not attempt to cut material that contains embedded objects unless you
know that the cutting tool fitted to your machine is suitable for the job
• Walls may conceal wiring and piping, car body panels may conceal fuel
lines, and long grass may conceal stones and glass. Always check the work
area thoroughly before proceeding
Beware of projected waste
• In some situations, waste material may be projected at speed from the
cutting tool. It is the user's responsibility to ensure that other people in the
work area are protected from the possibility of projected waste
Fitting cutting tools
• Ensure cutting tools are correctly and securely fitted and check that
wrenches / adjusters are removed prior to use
• Only use cutting tools recommended for your machine
• Do not attempt to modify cutting tools
Direction of feed
• Always feed work into the blade or cutter against the direction of movement
of the blade or cutter
Beware of heat
• Cutting tools and workpieces may become hot in use. Do not attempt to
change tools until they have been allowed to cool completely
Control dust / swarf
• Do not allow dust or swarf to build up. Sawdust is a fire hazard, and some
metal swarf is explosive
• Be especially careful when cutting wood and metal. Sparks from metal
cutting are a common cause of wood dust fires
• Where possible, use a dust extraction system to ensure a safer working
environment
www.silverlinetools.com
250W Bandsaw
7