Safety Regulations - EINHELL TC-HP 90 Manual De Instrucciones Original

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.

1. Safety regulations

Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fire and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
General safety regulations and
accident prevention
It is essential that you read the safety regulations
and operating instructions in their entirety and
follow the information contained therein in order
to eliminate the possibility of an accident or po-
tentially dangerous situation from occurring while
working with the high-pressure cleaner.
•
The electrical connection must be installed by
an electrician in accordance with IEC 60364.
•
The power plug must be plugged into a pro-
perly installed and earthed socket outlet with
connected earth-leakage circuit breaker (30
mA).
•
Always check the device, the mains cable
and the plug before using the high-pressure
cleaner. Only operate the device when it is in
good working order and has not been dama-
ged in any way. Damaged parts must be im-
mediately replaced by a qualified electrician.
•
Always pull the power plug out of the socket
outlet before doing any work on the high-
pressure cleaner, before changing the nozzle
and whenever the cleaner is not being used.
•
Only use suitable extension cables when wor-
king outdoors. Extension cables must have a
minimum cross-section of 1.5 mm
connections must have earthing contacts and
be rainwater-protected. Cables over 10 m in
length must have a cross section of at least
Anl_SA_TC_HP_90_SPK8.indb 27 Anl_SA_TC_HP_90_SPK8.indb 27
GB
2.5 mm
•
Warning! This device was developed to be
used with cleaning agents supplied or recom-
mended by the manufacturer. The use of any
other cleaning agents or chemicals can nega-
tively affect the safety of the device.
•
Warning! Do not use the device when other
persons or animals are in the near vicinity un-
less they are wearing appropriate protective
clothing.
•
Warning! High-pressure jets can be dange-
rous when the cleaner is not used properly.
Do not direct the jet toward persons, animals,
live electrical equipment or the device itself.
•
Warning! Do not direct the jet toward yourself
or others in order to clean clothes and foot-
wear.
•
Warning! Do not allow the high-pressure clea-
ner to be used by children or unauthorized
persons.
•
Warning! High-pressure hoses, fittings and
couplings are important components that
help to ensure device safety. Only use high-
pressure hoses, fittings and couplings that
are recommended by the manufacturer.
•
Warning! In order to ensure the operatio-
nal safety of the device, only use genuine
manufacturer's replacement parts or parts
that have been approved by the manufacturer.
•
Warning! Do not operate the device if the
mains cable or other important parts of the
device - e.g. safety-related elements, high-
pressure hoses, spray pistol - are damaged.
•
Do not pull or carry the electric tool by its
mains cable. Protect the mains cable from be-
coming damaged by oil, solvents and sharp
edges. Do not pull or carry the electric tool by
its mains cable.
•
Keep your place of work tidy.
•
Ensure that the switch is turned off when con-
necting the unit to the power supply.
•
Wear suitable work clothes.
•
Check your high-pressure cleaner to ensure
that it is in good working order. If the cleaner
is not functioning properly, have it checked by
an authorized professional. Have all mainte-
nance and inspection work carried out only by
a qualified electrician or ISC GmbH.
•
The water jet that emerges from the high-
pressure nozzle produces a „kickback" on
the spray pistol. Therefore, make sure that
. The plug you have a solid footing and that you have a
2
firm hold of the pistol grip. In order to protect
yourself from possible flying objects (that are
released due to the high pressure), wear sui-
- 27 -
.
2
05.10.2020 10:07:15 05.10.2020 10:07:15