Ds8.30E & Ds10.40E Pull-Type Assembly - Woods DS8.30E Manual Del Operador

Install SMV Emblem
1.
Align holes of SMV bracket (12) with top of splitter gearbox. Secure with
cap screws (36).
1. Tongue
2. Headless pin, 22.2 mm x 176.3 mm
(.875 x 6.94)
3. Sleeve, 22.5 mm x 28.9 mm x 66.5
mm (.885 x 1.125 x 2.62)
4. 11.1 mm x 8.73 mm (7/16 x 11/32)
Klik pin
5. Attitude rod
6. Wheel yoke
7. Tire & hub
8. H-Frame (DS10.40E only)
9. Shield (DS10.40E only)
10. Stub shaft (DS10.40E only)
11. CV Drive
12. SMV Bracket
13. SMV Emblem
14. Parking jack
15. Hydraulic cylinder
ASSEMBLE DS8.30E & DS10.40E 3-POINT MOUNTED
CUTTER
Refer to Figure 35.
Place jackstands under cutter to raise it off the ground to provide clearance
when assembling cutter. See "BLOCKING METHOD" on page 15 for jackstand
placement.
Install Rear Tailwheel
1.
Place assembled tailwheel arms (13 thru 25) between lugs on deck.
2.
Attach end of tailwheel arm to deck using cap screw (29) and flanged
lock nut (36).
3.
Align holes in middle of tailwheel arm with holes in lugs on rear of deck.
Secure with cap screw (29) and flanged lock nut (36).
NOTE:
Hole positions in lugs determine cut height. Final adjustment
will be necessary when cutter is mounted to tractor.
MAN1256 (3/23/2018)
16. Transport lock-up
17. 31.8 mm (1-1/4") Stroke control kit
18. Hydraulic hose, 3.9 m (154")
19. Cylinder vent plug
20. Hydraulic adapter
21. Hydraulic restricter
22. Male quick coupler
23. Headless pin, 25.4 mm x 101.6 mm
(1 x 4)
24. Headless pin 25.4 mm x 114.3 mm (1
x 4-1/2)
25. Pin, 25.4 mm x 103.6 mm (1.00 x
4.08)
26. 6.35 mm x 38.1 mm (1/4 x 1-1/2) Cotter
pin
27. 1/2 NC x 3 HHCS
28. 1/2 NC x 5-1/4 HHCS
Figure 34.
DS8.30E & DS10.40E Pull-Type Assembly
29. 1/2 NC Flanged lock nut
30. 3/8 Std flat washer
31. 3/8 NC x 1 HHCS
32. 1" Std flat washer
33. 1 NC Hex nut
34. 1 NC x 6 HHCS
35. 1 NC Hex lock nut
36. M12-1.75P x 30 mm HHCS
37. Bearing block (DS10.40E only)
38. Bearing (DS10.40E only)
39. Snap ring (DS10.40E only)
40. Grease fitting (DS10.40E only)
Install A-Frame
1.
Attach front A-frame bars (1) to square holes on inner mast plates using
carriage bolts (32), bushing sleeves (8), flat washers (35) and flanged
lock nuts (36).
2.
Install break links (2) and sleeve (4) between lower holes on A-frame
bars. Secure with cap screw (33) and lock nut (34).
3.
Attach lift arms (3) to lugs on rear of deck using cap screws (31) and
flanged lock nuts (36).
4.
Attach the two lift arms (3) together at the top rear hole using cap screw
(30), spacer sleeve (7), and flanged lock nut (36).
5.
Place both break links (2) together and position between front holes of lift
arms. Secure with cap screw (30), spacer sleeve (7), and flanged lock
nut (36).
NOTE:
Break links must rest on top of rear spacer sleeve (7).
6.
Install top link pin (6) and sleeve (5) into middle hole in top of A-frame
arms. Secure with cotter pin (26) and klik pin (27). Refer to CONNECT
CUTTER TO TRACTOR (MOUNTED) on page 15 for hitch pin
configurations.
Assembly 30