DeWalt DCH417 Traducido De Las Instrucciones Originales página 40

EnGLIsh
• Observe the relevant guidelines and national regulations for
your material, staff, application and place of application
(e.g. occupational health and safety regulations, disposal).
Wireless Tool Control (Fig. A)

CAUTION: Read all saftey warnings, instruction and
specifications of the appliance which is paired with
the tool.
Your tool is equipped with a Wireless Tool Control transmitter
which allows your tool to be wirelessly paired with another
Wireless Tool Control device, such as a D
To pair your tool using Wireless Tool Control, depress the trigger
switch
1 and the Wireless Tool Control pairing button on the
seperate device. An LED on the seperate device will let you
know when your tool has been successfully paired.
D WALT Tool Tag Ready (Fig. E)
e
Optional Accessory
Your tool comes with mounting holes
installing a D WALT Tool Tag. You will need a T20 bit tip to install
e
the tag. Only use the screws provided. The D
designed for tracking and locating professional power tools,
equipment, and machines using the D
app. For proper installation and use of the D
to the D WALT Tool Tag manual.
e
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
C
Lubrication
Your power tool requires no additional lubrication.
D
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
38
WALT dust extractor.
e
17 and fasteners for
WALT Tool Tag is
e
WALT Tool Connect™
e
WALT Tool Tag refer
e
Transport

CAUTION: Accidental starting during transport!
• Always transport your products with the batteries removed!
• Transport the tool and batteries individually packaged.
Follow the information in the section Battery Packs –
•
Transportation in this manual.
• Check the tool and batteries for damage before use
after transport.
Storage

CAUTION: Accidental damage caused by defective or
leaking batteries!
• Always store your products with the batteries removed!
• Store the tool and batteries in a place that is as cool and dry
as possible.
Follow the information in the section Battery Packs –
•
storage Recomendations in this manual.
• Store the tool and batteries in a place where they cannot be
accessed by children or unauthorized persons.
• Check the tool and batteries for damage before use after long
periods of storage.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
w
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that
can be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
• Run the battery pack down completely, then remove it from
the tool.
• Li‑Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
SDS plus® and SDS max® are registered trade marks of
Robert Bosch GmbH
WALT recommended
e