Overload Clutch; Assembly And Adjustments - DeWalt DCH417 Traducido De Las Instrucciones Originales

Release button
7
Main handle
8
SDS plus toolholder
9
Locking collar
10
Intended Use
Your cordless rotary hammerdrill has been designed for
professional drilling and hammerdrilling applications, as well as
screwdriving and chipping applications.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
Your cordless rotary hammerdrill is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.

Overload Clutch

In case of jamming of a drill bit, the drive to the drill spindle is
interrupted. Because of the resulting forces, always hold the
tool with both hands and take a firm stance. After the overload,
release and depress the trigger to re‑engage drive.

WARNING: Drill may stall if overloaded causing a sudden
twist. Always expect the stall. Grip the drill firmly to control
the twisting action and avoid injury.
Mechanical Clutch
These tools are fitted with a mechanical clutch. The indication
that the clutch has activated will be an audible ratcheting
together with increased vibration.
Anti-Rotation System (Fig. F)
In addition to the clutch, an anti‑rotation system offers increased
user comfort and safety through an on‑board, anti‑rotation
technology capable of detecting if the user loses control of
the hammer. When a jam is detected, the torque and speed are
reduced instantly. This feature prevents self rotation of the tool
reducing the occurrence of wrist injuries.
The anti‑rotation system indicator
indicate status.
Indicator Diagnosis
OFF Tool is
functioning
normally
SOLID Anti‑Rotation
System has
been activated
(ENGAGED)
Depth rod
11
Depth rod release button
12
Worklight
13
Anti‑rotation system LED
14
14 will illuminate to
Solution
Follow all warnings and instructions
when operating the tool.
With the tool properly supported,
release trigger. The tool will function
normally when the trigger is depressed
again and the indicator light will go out
Active Vibration Control
For best vibration control, hold the tool as described in Proper
Hand Position.
The active vibration control neutralises rebound vibration from
the hammer mechanism. Lowering hand and arm vibration,
it allows more comfortable use for longer periods of time and
extends the life of the unit.
The hammer only needs enough pressure to engage the active
vibraton control. Applying too much pressure will not make
the tool drill or chip faster and active vibration control will
not engage.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle

WARNING: Do not push the trigger when inserting
the battery
1. Align the battery pack 6
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge 19
button. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level of
charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Belt Hook (Fig. D)
Optional Accessory

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the tool
from a work belt. DO NOT use the belt hook for tethering
EnGLIsh
WALT battery packs and chargers.
e
6 is fully charged.
with the rails inside the tool's
7 and firmly pull the battery pack
, press and hold the fuel gauge
35