Residual Risks - Stanley FATMAX SFMCG700 Traducido De Las Instrucciones Originales

ENGLISH
Investigate and take corrective action to eliminate the
cause of wheel binding.
Do not restart the cutting operation in the workpiece.
u
Let the wheel reach full speed and carefully re-enter
the cut.
The wheel may bind, walk up or kickback if the power tool
is restarted in the workpiece.
Support panels or any oversized workpiece to mini-
u
mise the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut
and near the edge of the workpiece on both sides of the
wheel.
Use extra caution when making a "pocket cut" into ex-
u
isting walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
Safety warnings specific for wire brushing
opertions
Be aware that wire bristles are thrown by the brush
u
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The
wire bristles can easily penetrate light clothing and/or skin.
If the use of a guard is recommended for wire brush-
u
ing, do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand
@
in diameter due to work load and centrifugal forces.
Warning! Contact with or inhalation of dusts
arising from wire brushing applications may
endanger the health of the operator and possible
bystanders. Wear a dust mask specifically
designed for protection against dust and fumes
and ensure that persons within or entering the
work area are also protected.
Safety of others
This tool can be used by children aged from 8 years and
u
above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concern-
ing use of the appliance in a safe way and understand the
hazards involved.
Children shall not play with the appliance. Cleaning and
u
user maintenance shall not be made by children without
supervision.

Residual risks

Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
8
(Original instructions)
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving parts.
u
Injuries caused when changing any parts, blades or ac-
u
cessories.
Injuries caused by prolonged use of a tool. When using
u
any tool for prolonged periods ensure you take regular
breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed when
u
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by EN
60745 and may be used for comparing one tool with another.
The declared vibration emission value may also be used in a
preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following symbols are shown on the tool along with the
:
date code:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
O
Wear safety glasses or goggles when operating
this tool.
N
Wear ear protection when operating this tool.
Additional safety instructions for batteries and
chargers
Batteries
Never attempt to open for any reason.
u