Status Bar - Pulsar AXION LRF XQ38 Manual De Instrucciones

Defective Pixel
•
Select the Defective Pixel Repair
Repair
• (H) will appear on the left side of the
A marker
display.
•
A magnifying glass (G) will appear on the right side of
the display – a rectangle with an enlarged view of the
marker for precise pixel selection – and the coordinates
(I) of the marker under the magnifying glass.
•
Press the UP (4) and DOWN (2) buttons briefly to align a
defective pixel with the center of the enlarged marker
in the magnifying glass – the pixel should be removed.
Press the MENU (3) button briefly to switch the marker direction between the horizontal to
the vertical.
• Press the ON (5) button briefly to delete the dead pixel.
•
Once the pixel has been successfully deleted, an OK message will briefly appear on the
screen.
•
You can then delete the next defective pixel if required by moving the marker across the
display.
•
Press and hold the MENU (3) button to exit the function.
Restore Default
This option allows the user to return all previously disabled defective pixels to their original
Pixel Map
state.
•
Use the UP (4) / DOWN (2) buttons to select the Restore Default Pixel Map icon
•
Activate the function by briefly pressing the MENU (3) button.
•
Using the UP (4) / DOWN (2) buttons, select Yes if you want to return to the factory pixel
map and select No if you do not.
• Confirm your selection with a short press of the MENU (3) button.
Attention! One or two pixels on the display of the device in the form of bright white, black or
colored (blue, red or green) points may appear. These points cannot be removed and are not
a defect.
Device
This menu item allows the user to view the following information about the device:
Information द
SKU Number
द
Firmware Version
द
Device Name
द
Hardware Version
द
Device Serial Number
द
Service Information
•
To display information, do the following:
•
Press and hold the MENU (3) button to enter the main menu.
•
Use the UP (4) / DOWN (2) buttons to select the Device Information icon
•
Press the MENU (3) button briefly to view / exit the information.

STATUS BAR

The status bar is at the bottom of the display and displays information on the actual operating status of the
device, including:
•
Color Mode (shown only when the Black Hot color mode is selected)
•
Observation Mode
•
Calibration Mode (in Automatic calibration mode a countdown timer will appear instead of the calibration
mode icon 3 seconds before automatic calibration begins)
USER MANUAL FOR AXION LRF XQ38 THERMAL IMAGING SCOPE
option by briefly pressing the MENU (3) button.
.
.
•
Magnification
•
Time
•
Power Indication:
- charge level if the device is powered by a battery
- charge level if the device is charging and powered by a battery
- no battery, the device is connected to an external power supply
USING A BUILT-IN LASER RANGEFINDER
The AXION LRF XQ thermal imager is equipped with an integrated laser rangefinder.
SINGLE MEASUREMENT MODE
•
Press the ON/OFF (5) button briefly to power the device on.
•
Activate the rangefinder by pressing the DOWN (2) button briefly. A red mark appears on the display.
•
Place the rangefinder's reticle on the target. Press the DOWN (2) button briefly to measure the distance to the
object once.
•
The measurement results are displayed in the upper right corner.
•
The rangefinder shuts down after 3 seconds of inactivity.
SCAN MODE
•
Press the ON/OFF (5) button briefly to power the device on.
•
Activate the rangefinder by pressing the DOWN (2) button briefly. A red mark
appears on the display.
• Activate the scan mode by long pressing the DOWN (2) button to continuously
measure the distance to objects.
•
The measurement results are displayed in the upper right corner.
• Deactivate the rangefinder by long pressing the DOWN (2) button.
Notes:
द
Additional rangefinder settings are available in the "Rangefinder" section of
the main menu.
द
To select either Meters or Yards as the unit of measure please see the corresponding menu item.
द
When you turn on the rangefinder, the PiP window turns off.
OPERATING FEATURES:
•
The accuracy and distance of the measurement depends on the reflection coefficient of the object surface
and weather conditions. The reflection coefficient depends on the texture, color, size and shape of the object.
Generally, lighter colored objects and those with a shiny surface will have a higher reflection coefficient.
•
Measurement accuracy can be influenced by the light conditions, fog, haze, rain, snow, etc. The results may be
less accurate when operating in sunny weather or if the rangefinder is directed towards the sun.
•
It is easier and more reliable to measure the distance to large objects than to small ones.
DISPLAY OFF FUNCTION
This function deactivates the image transmission to the display by minimizing its
brightness. This helps prevent accidental disclosure. However, the device stays on.
When this function is in use, the device switches to the standby mode, which allows it to
be switched on quickly if necessary.
•
When the device is on, press and hold the ON (5) button for less than 3 seconds. The display goes blank and
the message Display Off appears.
• Press the ON (5) button briefly to turn on the display.
• When you press and hold the ON (5) button, the display shows the message Display Off with a countdown.
Holding the button down for the duration of the countdown will power the device off completely.
8