Maintenance And Care - Flex LK 602 VR Instrucciones De Funcionamiento Originales

 Attach the tool to the tool holder.
 Insert the mains plug into the socket.
 Switch on the polisher (without engaging it)
and run the polisher for approx.
30 seconds. Check for imbalances and
vibrations.
 Switch off the polisher.
klqb
tÜÉå=íÜÉ=éçïÉê=íççä=áë=ëïáíÅÜÉÇ=çÑÑI=íÜÉ=íççä=
ÅçåíáåìÉë=êìååáåÖ=ÄêáÉÑäóK
To remove the chuck:
 Pull out the mains plug.
 Press and hold down the spindle lock.
 Unscrew the chuck (Velcro pad, fleece
pad, sanding pad) anti-clockwise off the
spindle.
Attaching the tools
`^rqflk>
^íí~ÅÜ=íÜÉ=íççäë=áå=íÜÉ=ÅÉåíêÉ=çÑ=íÜÉ=íççä=ÜçäÇÉêK=
fãÄ~ä~åÅÉë=ã~ó=Ç~ã~ÖÉ=íÜÉ=éçïÉê=íççäK=
qÜÉ ïçêâ=êÉëìäí=ã~ó=ÄÉ=áãé~áêÉÇK
18

Maintenance and care

t^okfkd>
_ÉÑçêÉ=éÉêÑçêãáåÖ=~åó=ïçêâ=çå=íÜÉ=éçïÉê=íççäI=
éìää=çìí=íÜÉ=ã~áåë=éäìÖK
Cleaning
Regularly clean the power tool and ventilation
slots. Frequency of cleaning is dependent
on the material and duration of use.
Regularly blow out the housing interior and
motor with dry compressed air.
Carbon brushes
The polisher features cut-off carbon brushes.
When the wear limit of the cut-off carbon
brushes is reached, the polisher switches off
automatically.
klqb
rëÉ=çåäó=çêáÖáå~ä=é~êíë=ëìééäáÉÇ=Äó=íÜÉ=
ã~åìÑ~ÅíìêÉê=Ñçê=êÉéä~ÅÉãÉåí=éìêéçëÉëK=
fÑ åçåJçêáÖáå~ä=é~êíë=~êÉ=ìëÉÇI=íÜÉ=Öì~ê~åíÉÉ=
çÄäáÖ~íáçåë=çÑ=íÜÉ=ã~åìÑ~ÅíìêÉê=ïáää=ÄÉ=ÇÉÉãÉÇ=
åìää=~åÇ=îçáÇK
When the angle grinder is being used,
the carbon brushes can be seen sparking
through the rear air inlet apertures.
If the carbon brushes spark excessively, switch
off the polisher immediately. Take the polisher
to a customer service workshop authorised by
the manufacturer.
Gears
klqb
aç=åçí=äççëÉå=íÜÉ=ëÅêÉïë=çå=íÜÉ=ÖÉ~ê=ÜÉ~Ç=
ÇìêáåÖ=íÜÉ=ï~êê~åíó=éÉêáçÇK=kçåJÅçãéäá~åÅÉ=
ïáää=ÇÉÉã=íÜÉ=Öì~ê~åíÉÉ=çÄäáÖ~íáçåë=çÑ=íÜÉ=
ã~åìÑ~ÅíìêÉê=åìää=~åÇ=îçáÇK
Repairs
Repairs may be carried out by an authorised
customer service centre only.
Polisher LK 602 VR