Miller XMT 350 MPa Auto-Line Manual Del Operador página 13

Keep flammables away from cutting. Do not cut near flammables.
Welding sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
Do not cut on drums or any closed containers.
Stop engine before fueling.
Stop engine before fueling.
Stop engine before fueling.
When power is applied failed parts can explode or cause other parts to explode.
�
Hay una lista completa de piezas disponible en www.MillerWelds.com
Welding sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
Cutting sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
Do not grip material near cutting path.
Flying pieces of parts can cause injury. Always wear a face shield when servicing unit.
Do not fuel a hot engine.
Do not fuel a hot engine.
Do not fuel a hot engine.
Cutting sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it.
Do not weld on drums or any closed containers.
Turn off power before disassembling torch.
Always wear long sleeves and button your collar when servicing unit.
Use lift eye to lift unit and properly installed accessories only, not gas cylinders. Do not exceed maximum lift
Use lift eye to lift unit and properly installed accessories only, not gas cylinders. Do not exceed maximum lift e
Use lift eye to lift unit and properly installed accessories only, not gas cylinders. Do not exceed maximum lift
rating (see Specifications).
rating (see Specifications).
Do not weld on drums or any closed containers.
rating (see Specifications).
Do not cut on drums or any closed containers.
Do not remove or paint over (cover) the label.
After taking proper precautions as shown, connect power to unit.
Do not cut on drums or any closed containers. When power is applied failed parts can explode or cause other parts to explode.
When power is applied failed parts can explode or cause other parts to explode.
Do not grip material near cutting path. When power is applied failed parts can explode or cause other parts to explode.
Disconnect input plug or power before working on machine.
Flying pieces of parts can cause injury. Always wear a face shield when servicing unit.
Flying pieces of parts can cause injury. Always wear a face shield when servicing unit.
Turn off power before disassembling torch.
Do not grip material near cutting path.
Flying pieces of parts can cause injury. Always wear a face shield when servicing unit.
Turn off power before disassembling torch. Always wear long sleeves and button your collar when servicing unit.
Always wear long sleeves and button your collar when servicing unit.
Writer: If necessary, replace the word "handle" with "lift eye'.
Do not remove or paint over (cover) the label.
Always wear long sleeves and button your collar when servicing unit.
Writer: If necessary, replace the word "handle" with "lift eye'.
Do not use one handle to lift or support unit.
Do not use one handle to lift or support unit.
After taking proper precautions as shown, connect power to unit.
After taking proper precautions as shown, connect power to unit.
After taking proper precautions as shown, connect power to unit.
Do not remove or paint over (cover) the label.
Drive rolls can injure fingers.
Drive rolls can injure fingers.
Writer: If necessary, replace the word "handle" with "lift eye'.
Disconnect input plug or power before working on machine.
Disconnect input plug or power before working on machine.
Do not use one handle to lift or support unit.
Disconnect input plug or power before working on machine.
Welding wire and drive parts are at welding voltage during operation
Welding wire and drive parts are at welding voltage during operation
Drive rolls can injure fingers.
Consult rating label for input power requirements.
Consult rating label for input power requirements.
Welding wire and drive parts are at welding voltage during operation
Become trained and read the instructions and labels before working on machine.
Become trained and read the instructions and labels before working on machine.
Consult rating label for input power requirements.
Connect Green Or Green/Yellow grounding conductor to ground terminal first.
Connect Green Or Green/Yellow grounding conductor to ground terminal first.
Connect input conductors (L1, L2, L3) to line terminals.
Connect input conductors (L1, L2, L3) to line terminals.
Las chispas producidas por la soldadura pueden provocar incendios.
Tenga a mano un extinguidor y una persona que vigile lista para
usarlo.
No suelde sobre tambores u otros recipientes cerrados.
No quite esta etiqueta ni la cubra con pintura.
Desconecte el enchufe de la entrada o la alimentación antes de tra-
bajar en la máquina.
Al salir despedidos, los pedazos de las piezas pueden causar lesio-
nes. Use siempre careta de protección cuando repare la máquina.
Siempre use mangas largas y el cuello abotonado cuando esté repa-
rando la unidad.
Conecte la alimentación de la máquina únicamente después de ha-
ber tomado las precauciones indicadas.
No use una sola manija para levantar o sostener la unidad.
Consulte la etiqueta con los valores nominales para conocer los re-
quisitos de la entrada de alimentación.
Capacítese y lea las instrucciones y las etiquetas antes de trabajar
en la máquina.
keep hands and metal objects away.
keep hands and metal objects away.
keep hands and metal objects away.
OM-243477 Página 7
Safe
Safe1
Safe
Safe
Safe2
Safe2
Safe
Safe1
Safe1
Safe
Safe2
Safe
Safe
Safe
Safe1
Safe
Safe
Safe2
Safe
Safe
Safe
Safe
Safe
Safe2
Safe2
Safe2
Safe
Safe2
Safe
Safe2
Safe3
Safe
Safe2
Safe
Safe
Safe
Safe2
Safe2
Safe
Safe2
Safe2
Safe3
Safe3
Safe
Safe2
Safe2
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe
Safe3
Safe3
Safe
Safe
Safe
Safe