Lutron RCL-153PNL Guía De Instalación Rápida

LED + Dimmer
120 V~ 60 Hz
How-to videos
lutron.com/CLwiring
RCL-153PNL
150 W 600 W *
LED / CFL Incand. / Halogen
Please read before installing
English
WARNING: ELECTRIC SHOCK
HAZARD. May result in serious
injury or death. Turn off power at
circuit breaker or fuse
before installing.
Single Pole
For lights switched from one location:
Green wire
NOTE: Black and solid red wire on the dimmer are interchangeable.
AFTER INSTALLATION: Adjust low-end dimming range for LEDs and CFLs
1. Push shaft to turn lights on and rotate counter-clockwise
to adjust the low-end.
2. Move adjustment lever up or down to adjust the low-end
dimming range.
3. Push shaft to turn lights OFF and ON to verify proper
operation.
Mount Dimmer and Restore Power
1. Attach faceplate
For Troubleshooting, please visit www.lutron.com/support
Limited Warranty: www.lutron.com/TechnicalDocumentLibrary/369-119_Wallbox_Warranty.pdf
Lutron and LED+ are trademarks or registered trademarks of Lutron Electronics Co., Inc., in the U.S. and other countries.
The YouTube icon is a trademark of Google LLC.
Receive an Extended Warranty: www.lutron.com/CLregistration
Support: 1.844.LUTRON1 (USA / Canada)
Install with
confidence
Use included diagrams
or visit our website for
step-by-step instructions.
Ganging and Derating
Derating is necessary if mounting two
or more devices side by side (see
chart for new wattage rating).
Note: Derating not necessary for LED /
CFL loads.
* Maximum Allowable Inc. / Hal. Wattage
Single
Gang
600 W
Bend back
and forth
INSTALL WITH CONFIDENCE
VIDEO & STEP-BY-STEP INSTRUCTIONS VIDEO & STEP-BY-STEP INSTRUCTIONS
l u t r o n . c o m / C L w i r i n g
Before installing remove the rotary knob and the light ring.
Use blue
connector
Insert and
twist to
Ground wire
tighten
(bare or green)
2. Note the UP arrow
End of Gang Middle of Gang
450 W 300 W
Pull hard
For lights switched from two locations:
IMPORTANT:
(connected to the different colored screw)
before removing the old switch.
OR
Green wire
NOTE: Only one dimmer can be used in a 3-way circuit.
1.
3. Push the light ring on
©2020 Lutron Electronics Co., Inc.
+1.888.235.2910 (Mexico)
®
Quick Install Guide
Find the right LED
lutron.com/LEDfinder
Important Notes
1. CAUTION: Use only with permanently installed fixtures with
dimmable screw-in compact fluorescent, dimmable screw-in
LED, halogen, or incandescent lamps. To avoid overheating
and possible damage to other equipment, do not use to control
receptacles, motor-driven appliances, or transformer-supplied
appliances.
2. Install in accordance with all national and local
electrical codes.
3. When no "grounding means" exists in wallbox, the National
Electrical Code (NECR) allows a control to be installed as a
replacement when a plastic faceplate with plastic fasteners is
used, or the circuit is protected by a ground fault circuit interrupter
(GFCI). Lutron wallplates meet this requirement. Cap or remove
green wire before screwing control into wallbox.
4. Protect the dimmer from dust and dirt when painting or spackling
the wall.
5. It is normal for the dimmer to feel warm to the touch during
operation.
6. Clean the dimmer with a soft damp cloth only. Do not use any
chemical cleaners.
7. For indoor use only.
Pinch sides and
pull to remove ring
3-Way
Mark or tag the common wire
Tag
Insert and
twist to
tighten
NOTE: It may be helpful
to attach the knob for
2.
this step.
4. Push the knob on firmly
P/N 0301964 REV A
Ground wire
(bare or green)
Push hard