Protecting The Environment - DeWalt D28730 Traducido De Las Instrucciones Originales

Ocultar thumbs Ver también para D28730:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 28
1. Push in spindle lock 
and rotate wheel 
 12
wheel lock lever engages slot in inside flange 
wheel. Loosen the bolt 
 21
of the abrasive wheel with the 8 mm hex key 
right-hand thread.
2. Remove the bolt 
 21
, washer 
old wheel 
 10
.
3. Make sure flange surfaces are clean and flat. Install the new
abrasive wheel by reversing the above steps.
4. For safe operation, securely tighten bolt
the abrasive wheel
10
in between inner
flanges
. Do not overtighten bolt
23

WARNING: Check the work surface that the chop saw
rests on when replacing with a new abrasive wheel. It
is possible that the wheel may contact ANY ITEMS OR
STRUCTURE THAT EXTENDS ABOVE work surface
(under the base) when the arm is fully lowered.
Operation Tips for More Accurate Cuts
Allow the wheel to do the cutting. Excessive force will cause
the wheel to glaze reducing cutting efficiency and/or to
deflect causing inaccurate cuts.
Properly adjust fence angle.
Make sure material is laying flat across base.
Properly clamp material to avoid movement and vibration.
Motor Brush Inspection and Replacement
(Fig. H, I)
BE SURE TOOL IS UNPLUGGED BEFORE INSPECTING BRUSHES.
Brushes should be regularly inspected for wear. To inspect
brushes, unscrew the two end cap screws 
end cap 
 25 
. To remove each brush 
wire 
 27 
terminal connection. Then carefully back the brush
spring out of the brush box and remove brush. Brushes should
slide freely in brush box. If brushes are worn down to 8 mm as
shown in Figure I, they should be replaced.
To reinstall each brush, carefully back the spring out of the
brush box, insert the brush and return the spring making sure
it is pressing on the brush and not touching the brush box.
Reconnect shunt wire terminal, then replace the end cap and
two screws.
MAINTENANCE
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
by hand until
 10
 20
to lock
counterclockwise in the center
 7
. Bolt has
 22
, outside flange 
 23
and
21
to firmly secure
20
and outer
.
21
and remove the
 24 
 26 
, first unplug the shunt
Lubrication
Closed-type, grease-sealed ball bearings are used throughout.
These bearings have sufficient lubrication packed in them at the
factory to last the life of the chop saw.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Use only high-strength Type 1 organic bonded wheels rated
4100 rpm or higher according to EN12413, safety requirements
for bonded abrasive products.

Protecting the Environment

Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
EngLIsh
WALT recommended
e
25

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

D28730-qs

Tabla de contenido