UFESA AP9000 Manual De Instrucciones página 15

Ocultar thumbs Ver también para AP9000:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Preparing the vacuum cleaner for
operation
1
Insert the end of the suction hose to the vacuum
cleaner opening so that the markings
and on the vacuum cleaner housing are opposite each
other and turn the hose clockwise to the position
2
Connect the other end of the hose (handle) with
the telescopic suction tube.
3
Hold the ring on the pipe and set chosen length
putting it in or out.
4
Assemble the appropriate nozzle or brush to the
other end of the suction tube.
5
Use the following nozzles and brushes for traditional
vacuum cleaning with the SAFBAG dust bag and
vacuum cleaning with the use of the water filter module:
combination brush with small item separator, small nozzle,
small brush, crevice nozzle, parquet brush or turbo brush.
6
You may assemble a basket for picking up small
objects in the combination brush with small item
separator. In order to do so remove the basket cover
and insert the basket.
7
To clean hard surfaces – wooden floors, plastic
floors, ceramic tiles etc. pull out the brush by pressing
the switch on the nozzle according to the figure
8
The vacuum cleaner is equipped with an accessory
compartment. The compartment opens/closes with
the use of a slider. To open/close the compartment
side the slider downwards/upwards and take out/ put
away the desired nozzle.
9
The vacuum cleaner may be stored in a horizontal
position; in order to this, place the fastening hook of the
combination nozzle/brush into its fastening. The hose
may be left attached to the vacuum cleaner, but it is
important to pay attention not to leave it heavily bent
during storage.
10
Close the lid.
11
Grab the plug (4) and pull the cord out of the
vacuum cleaner.
While pulling out the cord pay attention
to the yellow stripe which signals the
end of the cord. Further attempts (pulling
on cord) may result in damaging the cord.
● Plug in the appliance.
Before switching on the vacuum cleaner
B
with the on/off button (8), make sure
that the appropriate module is installed
in the container (see section
on the hose end
"on/off" button (8).
In order to prepare the vacuum cleaner for wet
.
operation additionally:
attachment (24).
● Attach the hose fastenings to the suction hose and
the telescopic suction tube.
suction tube and insert the other end of the hose in the
small atomizing nozzle or the large atomizing nozzle
until you hear a characteristic click.
wet cleaning function or to pick up water: large atomizing
nozzle, small atomizing nozzle or the water pick up nozzle.
● Insert the stub pipe of the hose to the valve in the
vacuum cleaner housing.
● Make sure the stub pipe fastenings snap shut.
In case of difficulties in connecting the
.
above mentioned elements moisten the
gaskets e.g. with technical vaseline,
water, etc.
Vacuum cleaner functions
TRADITIONAL CLEANING WITH SAFBAG
DUST BAG
Vacuum cleaner is equipped with SAFBAG bag (1 piece).
and lift the container lid.
(filtration unit and partition).
dust bag to the container.
● Prepare the vacuum cleaner for operation according
to section
it had been working before it was turned off. Set the
desired power value by pressing the power adjustment
buttons +/- (9).
12
Switch on the vacuum cleaner by pressing the
13
Assemble the spray unit – the suction hose handle
14
Attach the end of the hose (sleeve) to the telescopic
15
Use the following nozzles for the wet vacuuming and
16
Slide the stub pipe valve plug downwards.
1
Press and hold the container lid opening button (2)
2
Remove the water filter module from the container
3
Insert the dry filtration module with the SAFBAG (21)
B
.
4
The vacuum cleaner starts at the same power level
,
, or
).
C
E
F
C

Publicidad

Tabla de contenido
loading

Tabla de contenido