Manual Registration In The Home Network; Logging In To Your Home Network Automatically (Wps) - Gaggenau VL 414 712 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

en-us
Home Connect
Manual Registration in the Home
Network
Note: To log in to the home network (Wi-Fi) manually,
you require the network name (SSID) and password (key)
for your home network.
1.
Turn the control knob clockwise to the < position.
After around 5 seconds, the illuminated ring around
the control knob flashes blue and yellow alternately.
The appliance is now in manual mode.
2.
Switch to the general settings menu of your mobile
device and call up the Wi-Fi settings.
On your mobile device, the "HomeConnect" Wi-Fi
connection is available for around 20 minutes.
3.
Connect to the "HomeConnect" Wi-Fi connection
(password: "HomeConnect").
4.
Launch the Home Connect app on your mobile device
and follow the instructions for network login. Enter the
password (key) of the home network. Following
successful connection to the router, the illuminated
ring around the control knob lights up green for
around 3 seconds.
5.
The illuminated ring around the control knob flashes
blue and white alternately. The connection to the
mobile device is being established.
The appliance is available in the app on the mobile
device once the illuminated ring around the control
knob lights up green. If the illuminated ring around the
control knob lights up red, it was not possible to
establish a connection
6.
To save the connection, exit the Home Connect
settings menu. ~ "Exiting the Home Connect
settings menu" on page 19
7.
After successfully connecting, push in the control
knob and turn it counterclockwise to the h position.
Otherwise, it is not possible to operate the appliance
using the Home Connect app.
Connection to the router unsuccessful
1.
If a connection could not be established, check the
router and turn the control knob to another position
and then back to the < position.
The illuminated ring around the control knob lights up
blue. After around 5 seconds, the illuminated ring
around the control knob flashes blue and yellow.
2.
Switch to the general settings menu of your mobile
device and start the Wi-Fi connection again.
3.
Check that the password has been entered correctly.
18
Connection to the mobile device unsuccessful
1.
If a connection could not be established, turn the
control knob to another position and then back to the
< position.
The illuminated ring around the control knob lights up
blue. After around 5 seconds, the illuminated ring
around the control knob flashes blue and white.
2.
Launch the Home Connect app on your mobile device
and follow the instructions for automatic network
login.
Connecting more mobile devices to the same Home
Connect account
In the Home Connect app, you can connect more mobile
devices to your appliance.
Connecting more mobile devices to another Home
Connect account
Prerequisite: A mobile device is connected to the
appliance. The appliance can be found in the Home
Connect settings menu.
1.
Turn the control knob to another position and then
back to the < position.
The illuminated ring around the control knob flashes
blue and white. The appliance is now ready to connect
to another mobile device.
2.
Launch the Home Connect app on your mobile device
and follow the instructions for automatic network
login.
The appliance is available in the app on the mobile
device once the illuminated ring around the control
knob lights up green.
Logging in to your home network
automatically (WPS)
You require a router that has WPS functionality. You will
find information about this in the manual for your router.
You need to be able to access your router.
If this is not the case, follow the steps in ~ "Manual
Registration in the Home Network" on page 18.
1.
Push in the control knob and turn it to position 1.
During the connection process, the illuminated ring
around the control knob flashes blue and yellow
alternately.

Publicidad

Tabla de contenido
loading

Tabla de contenido