Switch The Wireless Network Connection (Lan Or Wlan) On Or Off; Changing From Wi-Fi Connection To Lan Connection; Changing From Lan Connection To Wi-Fi Connection; Resetting The Home Connect Connections - Gaggenau VL 414 712 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

en-us
Home Connect
Switch the wireless network connection
(LAN or WLAN) on or off
You can switch off the LAN or Wi-Fi on your cooktop
extractor system at any time (e.g. to save energy during a
holiday). The connections to the home network and to the
cooktop remain saved. When you switch the LAN or Wi-Fi
back on, the saved connections are applied.
1.
Carry out the following operating steps one after the
other without interruption.
Open the Home Connect settings menu. ~ "Open
2.
or close the Home Connect settings menu"
on page 16
The illuminated ring around the control knob lights up
blue.
3.
Turn the control knob clockwise to position 3. The
illuminated ring around the control knob lights up
green.
After around 5 seconds, the illuminated ring around
the control knob flashes blue. After a few seconds,
the illuminated ring around the control knob lights up
blue. The network connection is deactivated.
Close the Home Connect settings menu. ~ "Open
4.
or close the Home Connect settings menu"
on page 16
The illuminated ring on the control knob goes out.
If you want to switch the network connection back on,
work through the same operating sequence. The
illuminated ring around the control knob lights up blue.
After around 5 seconds, the illuminated ring around the
control knob flashes blue and then lights up green.
Note: If the cooktop extractor system is directly
connected to a cooktop, the Wi-Fi can not be switched
off.
Changing from Wi-Fi connection to
LAN connection
1.
Connect the cooktop extractor system to the router
(RJ45 cable).
2.
Carry out the following operating steps one after the
other without interruption.
Open the Home Connect settings menu. ~ "Open
3.
or close the Home Connect settings menu"
on page 16
The illuminated ring around the control knob lights up
green.
4.
Turn the control knob clockwise to the μ position.
After approx. 5 seconds, the illuminated ring for the
control knob lights up blue. The connection is
established via LAN.
20
Close the Home Connect settings menu. ~ "Open
5.
or close the Home Connect settings menu"
on page 16
The illuminated ring on the control knob goes out.
Changing from LAN connection to Wi-Fi
connection
1.
Carry out the following operating steps one after the
other without interruption.
Open the Home Connect settings menu. ~ "Open
2.
or close the Home Connect settings menu"
on page 16
The illuminated ring around the control knob lights up
blue.
3.
Turn the control knob clockwise to the μ position.
After approx. 5 seconds, the illuminated ring for the
control knob lights up green. The connection is
established via Wi-Fi.
4.
Disconnect the connection between the cooktop
extractor system and the router (RJ45 cable).
Resetting the Home Connect
connections
You can reset the connections you have saved for your
home network and cooktop at any time.
1.
Carry out the following operating steps one after the
other without interruption.
Open the Home Connect settings menu. ~ "Open
2.
or close the Home Connect settings menu"
on page 16
The illuminated ring around the control knob lights up
blue.
3.
Turn the control knob clockwise to the Ž position.
After approx. 30 seconds, the illuminated ring for the
control knob lights up green. All Home Connect
settings have been reset. The appliance will no longer
be displayed in the Home Connect app.
Close the Home Connect settings menu. ~ "Open
4.
or close the Home Connect settings menu"
on page 16
The illuminated ring on the control knob goes out.

Publicidad

Tabla de contenido
loading

Tabla de contenido