Publicidad
Enlaces rápidos
Task Chair
Silla de trabajo
Assembly Instructions
Instrucciones de ensamblaje
Model Number / Número de modelo: 49230 / 49701
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
ESTE FOLLETO DE INSTRUCCIONES TIENE IMPORTANTE INFORMACIÓN SOBRE
SEGURIDAD. POR FAVOR LÉALO Y GUÁRDELO PARA SU REFERENCIA EN EL FUTURO.
Lot Number / Número de lote:
Date of purchase / Fecha de compra:
Publicidad
Manuales relacionados para Serta 49230
Resumen de contenidos para Serta 49230
- Página 1 Task Chair Silla de trabajo Assembly Instructions Instrucciones de ensamblaje Model Number / Número de modelo: 49230 / 49701 THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. ESTE FOLLETO DE INSTRUCCIONES TIENE IMPORTANTE INFORMACIÓN SOBRE...
-
Página 2: Instrucciones De Ensamblaje
Chair Assembly Instructions Carefully unpack all parts and identify them against the parts list before attempting to assemble. To avoid scratching the components, assemble the chair on a protected surface. Note: The casters sold with this chair are intended for use on carpet and not recommended for use on tile or hard wood floors. - Página 3 PARTS/PARTES Casters Star Base Gas Lift Seat Plate Ruedas Base en forma de estrella Mecanismo del asiento Elevador neumático Quantity/cantidad: 5 Quantity/cantidad: 1 Quantity/cantidad:1 Quantity/cantidad: 1 Back Cushion Seat Cushion Left Arm Right Arm Cojín del respaldo Cojín del asiento Brazo izquierdo Brazo derecho Quantity/cantidad: 1...
- Página 4 Step 1 Place the Star Base (B) upside down and insert 5 Casters (A) into the holes on the Star Base (B). Paso 1 Ponga la base en forma de estrella (B) con las patas hacia arriba y inserte las 5 ruedas (A) en los hoyos situados en la base (B).
- Página 5 Step 3 Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front of the seat plate facing the front of seat cushion). Attach by using 1-1/4” Big Screws (I) for the front holes of the Seat Plate (D) and 1” Big Screws (H) for the rear holes of the Seat Plate (D) and tighten screws.
- Página 6 Step 4 Insert Levers (D1 & D2) of Seat Plate (D) to the pre-attached cable lever receivers on the underside of Seat Cushion (F) (with the front of the levers facing the front of seat cushion). Push down the key on the receivers to pull out the levers.
- Página 7 Step 5 Tighten the brackets of Arms (E1 & E2) onto the bottom of the Seat Cushion (F) (with front of arms facing the front of seat cushion) by using 1-1/4” Small Screws with Flat Washers (K) for the inner holes of the arms and 2-1/4” Small Screws with Flat Washers (J) for the outer holes of the arms.
- Página 8 Step 6 Align the Back Cushion (G) with the Seat Cushion (F) by positioning the back support plate over the Seat Plate (D) with 1-1/4” Big Screws (I). *Note: Tighten the screws completely. Paso 6 Alinee el cojín del respaldo (G) con el cojín del asiento (F) por medio de colocar la placa de soporte del respal sobre la placa del asiento (D) con tornillos grandes de 32mm (I).
- Página 9 Step 7 Position the assembled chair upright with the seat plate facing down. Insert the Gas Lift (C) into the center hole of the Seat Plate (D). Paso 7 Coloque la silla ensamblada verticalmente, con la plancha del asiento hacia abajo. Inserte el elevador neumático (C) en el hoyo central de la mecanismo del asiento (D).
-
Página 10: Function Instruction
Operating Instructions Instrucciones de Uso Function Instruction - 1 To Adjust Seat Height: While seated, lean forward and reach under the right side of the chair to find the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height. - Página 11 Function Instruction - 2 To Operate Tilt Lockout: While seated, reach under the left side of the chair to find the lever. Push down the lever and lean back to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and pull the lever to the up position.
- Página 12 Function Instruction - 3 To Adjust Tension On The Tilt: Reach under the front center of the chair, grasp the round knob (R) and turn it counter - clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user.
- Página 13 Function Instruction - 4 To Adjust Arm Height: Pull up the buttons on the chair arms. Pull up the buttons to allow the arms to move up or down freely then release the buttons once desired height is reached. Instrucciones de Funcionamiento - 4 Para Ajustar la Altura de los Brazos: Jale los botones de los reposabrazos de la silla.
- Página 14 Function Instruction - 5 360˚ Swivel: 360˚ Seat swivel. Instrucciones de Funcionamiento - 5 Giro de 360˚: Giro de 360˚ del asiento.
- Página 15 Limited Warranty True Innovations seating products are warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases True Innovations furniture from an authorized True Innovations retailer as shown by the original sales receipt. This warranty does not apply to “as is” or previously owned seating products.
-
Página 16: Garantía Limitada
Garantía Limitada Los asientos de True Innovations están garantizados contra defectos de material y mano de obra mientras continúen bajo la propiedad del “comprador original”. El “comprador original” se define como la parte o entidad que compra muebles True Innovations de un minorista de True Innovations autorizado, tal como se indique en el recibo de venta original. Esta garantía no cubre asientos “en el estado en que se encuentran”...