American Standard 2823 Serie Instrucciones De Instalación

TISSUE HOLDER
SOPORTE PARA PAPEL HIGIÉNICO
SUPPORT DE PAPIER TOILETTE
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years. To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Gracias por seleccionar los productos American Standard, sinónimo de la mejor calidad
durante más de 100 años. Por favor lea estas instrucciones detenidamente antes de
comenzar para que lleve a cabo la instalación sin contratiempos.
Nous vous remercions d'avoir choisi American Standard... synonyme de qualité supérieure
depuis plus de 100 ans. Pour vous assurer que l'installation se déroulera sans difficulté,
veuillez lire attentivement ces instructions avant de commencer.
Recommended Tools & Materials/Herramientas y Materiales Recomendados/Outils et matériaux recommandés
10'
Tape Measure
Flexómetro
Ruban à mesurer
1
INSTALL MOUNTING PLATES
The TISSUE HOLDER (1) works best if secured to a wall stud or cross brace within the wall, using the SCREWS (3) supplied.
If the TISSUE HOLDER (1) is to be installed on a tile or plaster wall the ANCHORS (4) and SCREWS (3) should be used.
Note: The center line distance (6-1/4") between the MOUNTING PLATES (5) is critical, and must be maintained.
Determine desired height and location (optional) and mark a center line. Using the MOUNTING PLATE (5) as a template mark the two
spots for the anchors. If MOUNTING PLATE (5) is secured to a stud or cross brace drill small pilot holes for SCREWS (3).
For installations on drywall, use ANCHORS (4) and SCREWS (3) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips screwdriver
or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with the wall. The
TISSUE HOLDER BODIES (2) are mounted 6-1/4" center to center. Place MOUNTING PLATE (5) over ANCHORS (4) and insert screws
provided with #2 Phillips screwdriver. See illustration below. Repeat above steps for remaining MOUNTING PLATES (5).
For installations on tiled walls, pre drill a 1/4" hole through the tile only. Do not drill into the drywall. Use ANCHORS (4) and
SCREWS (3) for securing MOUNTING PLATE (5) to tiled wall. Place #2 Phillips screwdriver or cordless screwdriver into recess of anchor.
Press into drywall while turning the anchor clockwise until it is seated flush with the tiled wall. The TISSUE HOLDER BODIES (2) are
mounted 6-1/4" center to center. Place MOUNTING PLATE (5) over ANCHORS (4) and insert screws provided with #2 Phillips screwdriver.
See illustration below. Repeat above steps for remaining MOUNTING PLATES (5).
Secure MOUNTING PLATE (5) to wall with SCREWS (3).
6-1/4"
6-1/4" (159 mm)
159 mm (6-1/4 po.)
4
5
3
Installation Instructions
Instrucciones de instalación
Mode d'installation
Drill
Taladro
Perceuse
CENTER LINE
LÍNEA CENTRAL
LIGNE CENTRALE
USE MOUNTING PLATE AS TEMPLATE
USE LA PLACA DE MONTAJE COMO PLANTILLA
UTILISER UNE PLAQUE DE MONTAGE COMME GUIDE
4
CENTER LINE
LÍNEA CENTRAL
LIGNE CENTRALE
2823 SERIES
SERIE 2823
SÉRIE 2823
Certified to comply with ANSI A112.18.1
Certificación de cumplimiento de la norma ANSI A112.18.1
Certifié conforme à ANSI A112.18.1
U.S. Patent No. D403,750
Patente estadounidense D403,750
Brevet U.S.A. no. D403,750
Regular Screwdriver
Desarmador plano
Tournevis plat
1
3
5
FINISHED WALL
PARED TERMINADA
MUR FINI
M 9 6 8 3 8 5 C
Phillips Screwdriver
Desarmador de cruz
Tournevis cruciforme
2