Yamaha QL5 Manual De Referencia página 274

I DYNA.PHASER
Two input, two output dynamically controlled phaser.
Parameter Range
SOURCE INPUT, MIDI Control source: input signal or MIDI Note On velocity
SENSE 0–100 Sensitivity
DIR. UP, DOWN Upward or downward frequency change
*1
DECAY Decay speed
OFFSET 0–100 Lowest phase-shifted frequency offset
Feedback gain (plus values for normal-phase feedback, minus values for
FB.GAIN –99 to +99%
reverse-phase feedback)
STAGE 2, 4, 6, 8, 10, 12, 14, 16 Number of phase shift stages
LSH F 21.2 Hz–8.00 kHz Low shelving filter frequency
LSH G –12.0 to +12.0 dB Low shelving filter gain
HSH F 50.0 Hz–16.0 kHz High shelving filter frequency
HSH G –12.0 to +12.0 dB High shelving filter gain
*1. 6.0 ms–46.0 s (fs=44.1 kHz), 5.0 ms–42.3 s (fs=48 kHz)
I HQ.PITCH
One input, two output high-quality pitch shifter.
Parameter Range
PITCH –12 to +12 semitones Pitch shift
FINE –50 to +50 cents Pitch shift fine
DELAY 0.0–1000.0 ms Delay time
Feedback gain (plus values for normal-phase feedback, minus values for
FB. GAIN –99 to +99%
reverse-phase feedback)
MODE 1–10 Pitch shift precision
SYNC OFF/ON Tempo parameter sync on/off
*1
NOTE Used in conjunction with TEMPO to determine DELAY
*1.
Description
Description
(Maximum value depends on the tempo setting)
I DUAL PITCH
Two input, two output pitch shifter.
Parameter Range
PITCH 1 –24 to +24 semitones
FINE 1 –50 to +50 cents
LEVEL 1 –100 to +100%
PAN 1 L63 to R63
DELAY 1 0.0–1000.0 ms
FB. G 1 –99 to +99%
MODE 1–10
PITCH 2 –24 to +24 semitones
FINE 2 –50 to +50 cents
LEVEL 2 –100 to +100%
PAN 2 L63 to R63
DELAY 2 0.0–1000.0 ms
FB. G 2 –99 to +99%
SYNC OFF/ON
*1
NOTE 1
NOTE 2 *1
*1.
I TREMOLO
Two input, two output tremolo effect.
Parameter Range
FREQ. 0.05–40.00 Hz
DEPTH 0–100%
WAVE Sine, Tri, Square
SYNC OFF/ON
*1
NOTE
LSH F 21.2 Hz–8.00 kHz
LSH G –12.0 to +12.0 dB
EQ F 100 Hz–8.00 kHz
EQ G –12.0 to +12.0 dB
EQ Q 10.0–0.10
HSH F 50.0 Hz–16.0 kHz
HSH G –12.0 to +12.0 dB
*1.
12
Description
Channel #1 pitch shift
Channel #1 pitch shift fine
Channel #1 level (plus values for normal phase, minus values for reverse
phase)
Channel #1 pan
Channel #1 delay time
Channel #1 feedback gain (plus values for normal-phase feedback, minus
values for reverse-phase feedback)
Pitch shift precision
Channel #2 pitch shift
Channel #2 pitch shift fine
Channel #2 level (plus values for normal phase, minus values for reverse
phase)
Channel #2 pan
Channel #2 delay time
Channel #2 feedback gain (plus values for normal-phase feedback, minus
values for reverse-phase feedback)
Tempo parameter sync on/off
Used in conjunction with TEMPO to determine Channel #1 delay
Used in conjunction with TEMPO to determine Channel #2 delay
(Maximum value depends on the tempo setting)
Description
Modulation speed
Modulation depth
Modulation waveform
Tempo parameter sync on/off
Used in conjunction with TEMPO to determine FREQ
Low shelving filter frequency
Low shelving filter gain
EQ (peaking type) frequency
EQ (peaking type) gain
EQ (peaking type) bandwidth
High shelving filter frequency
High shelving filter gain
Data List