Unpacking The Product; Unfolding The Stroller - Joovy Toy Caboose 04X Manual Del Usuario

EN FR ES
Please read these instructions carefully before use and keep them for future reference.
• This product is a TOY stroller for dolls or stuffed toys ONLY.
• NEVER use this toy to carry a baby or child for any purpose whatsoever. Death or Serious Injury may occur.
• Maximum weight allowed = 5 lbs. (2.28 kg) in EACH seat.
• DO NOT stand on platform. Riding is for dolls or stuffed toys ONLY.
• This product contains small parts. Adult assembly is required.
• The maximum weight that can be carried in the storage basket is 5 lbs. (2.28 kg).
• Discard all packaging materials properly. Do not allow children to play with them.
• Discontinue use of this toy should it malfunction or become damaged.
• Please contact our customer service department to arrange for repair or obtain replacement parts.
• Do not use this toy on stairways or escalators.
• Hanging bags or other toys from the handlebars or any other parts of this toy may change its balance and cause a
hazardous unstable condition.
• When installing a toy infant carrier onto the stroller, ALWAYS use the restraining strap to secure the carrier in place.
If you experience any difficulty with the assembly or use of this product, or if you have a question regarding these
UNITED STATES – Joovy: (877) 456-5049, Hours 8:30 am – 5:00 pm Central Time.

1 Unpacking the Product

• Remove everything from the box and identify the parts using Figure 1.1. (not to scale)
A: stroller, B: canopy, C: tray, D: car seat carrier support, E: front wheels (2), F: rear wheels (2), G: rear axle, H: hubcaps (2),
I: washers (2), J: axle locks (2), K: axle caps (2), and documents (not shown)
• Discard all packaging materials properly including plastic coverings.
• DO NOT allow children to play with any packaging materials.

2 Unfolding the Stroller

• Orient the stroller with the handle bar away from you.
• Release the locking latch located on the lower right side by lifting up the lever. See Figure 2.1.
• Lift up on the stroller handle with both hands until the stroller is in the open position and both side frame bars snap into place in their
holders.
3 Installing the Rear Wheels
• Turn your stroller upside down so that it is resting on the seatback.
• Locate the rear axle and slide it through the holes into the frame near the platform.
• Locate a metal washer and slide the washer onto one end of the axle. See Figure 3.1.
• Locate a rear wheel and slide the wheel onto the axle.
IMPORTANT NOTE: The left and right side wheels are slightly different. The correct wheel will have the arrow shapes on the tire tread
pointed towards the REAR of the stroller. BE CERTAIN that the wheels are placed on the correct side of the axle, because this is intended
to be a one-time assembly.
• Locate an axle lock. While holding the axle from the opposite side, orient the axle lock with the larger side closest to the wheel and snap it
onto the axle. See Figure 3.2.
• Fit a rear axle cap over the attachment. You will hear this piece snap into place. See Figure 3.3.
• While holding the wheel, line up the four prongs on the hubcap with the holes in the spoke of the wheel and snap into place. BE CERTAIN
that all four prongs snap into place. Pull on the hubcap to be sure it is installed securely.
• Repeat these steps on the other side.
• Ensure that each wheel assembly is secure before using this toy. Pull on the wheels to be sure they are installed correctly.
Please do not return this product to the store
instructions, please contact our Customer Service Department:
CANADA – ISSI Inc.: (800) 667-4111, Hours 8:30 am – 5:00 pm Eastern Time.
Please note: Styles and colors may vary.
Adult assembly required. No tools required. Package contains small parts.
Keep small parts out of children's reach during assembly.
WARNING
!
WARNING
!