Chamberlain LiftMaster 1000 Manual Del Usuario página 24

INSTALL THE PROTECTOR SYSTEM™
(See Accessories)
The force, as measured on the closing edge of the door, should not
exceed 150 N (15kg). If the closing force is adjusted to more than
150 N, The Protector System™ must be installed.
After the opener has been installed and adjusted, The Protector
System™ accessory can be installed. Instructions are included with this
accessory.
The Protector System™ provides an additional measure of safety
against a small child being caught under a garage door.
It uses an invisible beam which, when broken by an obstruction, causes a
closing door to open and prevents an open door from closing. It is strongly
recommended for homeowners with young children.
Models 800 and 1000: The Protector System™ must be installed before
activating the auto close feature.
PROGRAM YOUR OPENER AND REMOTE
(If supplied)
Activate the opener only when door is in full view, free of obstruction
and properly adjusted. No one should enter or leave garage while
door is in motion.
Your garage door opener receiver and remote control transmitter are set
to a matching code. If you purchase additional remote controls, the garage
door opener must be programmed to accept the new remote code.
TO PROGRAM THE RECEIVER
TO MATCH ADDITIONAL REMOTE CONTROL CODES
1. Press and hold the remote control push button (1).
2. Press and release the PROG button (2) on the control panel. The
opener lights will flash once.
3. Release the remote push button.
Now the opener will operate when the remote control push button is
pressed.
If you release the remote control push button before the opener lights
flash, the opener will not accept the code.
TO ERASE ALL REMOTE CONTROL CODES
• Press and hold the PROG button on the control panel until the indicator
light (3) turns off (about 6 seconds). All the codes the opener has
learned will be erased.
• To reprogram, repeat Steps 1 – 3 for each remote control in use.
OPERATION OF YOUR OPENER
Your opener can be activated by any of the following devices:
• The wall mounted door control. Hold the push button down until door
starts to move.
• The Outside Keylock or Keyless Entry System (if you have installed
either of these accessories).
• The Remote Control Transmitter. Hold the push button down until the
door starts to move.
• (Models 800 and 1000 only) The left push button on the control
panel, when the opener is not in a learn or limit setting mode (the
indicator light must not be on).
OPENING THE DOOR MANUALLY
Door should be fully closed if possible.
A. C-rail: The door can be opened manually by pulling the trolley release
handle down. To reconnect the trolley, rotate the lever. It will reconnect
on the next up or down operation.
B. T-rail: The door can be opened manually by pulling the trolley release
handle down and back (toward the opener). To reconnect the trolley,
pull the release handle straight down. It will reconnect on the next up
or down operation.
Do not use the manual release handle to pull the door open or
closed.
114A2445C-GB
WHEN THE OPENER IS ACTIVATED BY THE REMOTE CONTROL
21
1. If open, the door will close. If closed, the door will open.
2. If moving, the door will stop.
3. If the door has been stopped while moving, it will next move in the
opposite direction.
4. If an obstruction is encountered while closing, the door will reverse.
5. If an obstruction is encountered while opening, the door will stop.
6. The optional Protector System™ uses an invisible beam which, when
broken by an obstruction, causes a closing door to open and prevents
an open door from closing. It is STRONGLY RECOMMENDED for
homeowners with young children.
The opener light will turn on: 1) when opener is initially plugged in;
2) when the power is interrupted; 3) when the opener is activated.
The light turns off automatically after 2-1/2 minutes. Bulb size is 40 Watts
maximum (230V, E27).
22
CARE OF YOUR OPENER
When properly installed, opener will provide high performance with a
minimum of maintenance. The opener does not require additional
lubrication.
Limit and Force Adjustments: These adjustments must be properly set
and checked when the opener is installed. Weather conditions may cause
some minor changes in the door operation, requiring some re-
adjustments, particularly during the first year of operation.
Refer to the limit and force adjustments on page 4. Follow the instructions
carefully and repeat the safety reverse test after any adjustment.
Remote Control Transmitter: The lithium batteries should produce
power for up to five years. To replace batteries, use a screwdriver blade to
pry open the case along the side where "Open" is stamped on the back.
Insert batteries positive side down. To replace cover, snap shut along both
sides.
Do not dispose of old batteries with household waste. Take batteries to a
proper disposal center.
Additional remotes can be purchased at any time for use in all vehicles
using garage. Refer to Accessories. The receiver must be programmed to
operate with any new remote.
MAINTENANCE OF YOUR OPENER
• Repeat safety reverse test. Adjust if necessary.
• Check to be sure door opens and closes fully. Adjust Limits and/or Force
if necessary.
Oil door rollers, bearings and hinges. The opener does not require
additional lubrication. Do not grease the door tracks.
OR WALL MOUNTED DOOR CONTROL:
Once a Month:
Manually operate door to check for imbalance or binding.
Examine your installation, cables, springs and mountings for
wear or damage. Call for professional garage door service if
necessary. To avoid possible injury, do not use until repaired.
Once a Year: