Ash Removal; Safety Regulations; Advice On Chimney-Sweeping And Stove And Smoke Flue Maintenance - deville C07931 Instrucciones De Instalacion Y Uso

•
When the loading of small parts of wood is well lit,
open the door, load the appliance with the
recommended fuel.
7.4.2 - Working
•
The wanted speed is obtained in moving the
different components (see Fig. 18) and in choosing
a load corresponding to the needs.
•
To get a slower speed for a longer period, load on a
hardly glowing bed of embers.
•
To get a rapid blaze, restart the fire with small parts
of wood, load with logs, possibly maintaining the
door slightly open for a few minutes to accelerate
the blaze, keeping
surveillance, then close the door. This operation
allows to accelerate the restart, especially if the
wood is humid.
•
Adjust the speed changes (going from a normal
speed to a slower speed for example) before
loadings in the embers'combustion stage, to let the
appliance and the smokes' flue progressively
change speed.
•
In order to avoid smoke blowing back and falling
down of the ashes in the room when you reload, the
opening of the door needs to take a few
precautions :
- Stop the ventilation in order to avoid vacuuming
the ashes that might fall before the appliance (only
C07932).
- Open slightly the door, pause for a moment to
start the draught corresponding to the running with
a open door, then slowly open the door.
•
The continuous running with a slow speed,
especially in milder weather (unfavourable draught)
and with humid wood, leads to an incomplete
burning which favour bistre and tar deposits :
Alternate slow speeds with some returns to
o
normal speed running period.
Favour uses with small loads.
o
•
After a running with a slow speed, the window can
get dark because of a slight bistre. This deposit
normally disappears in a higher speed pyrolysis
running.
•
The combustion chamber must be always closed
except when reloading in order to avoid any excess
of smoke.

Ash removal

7.4.3 -
•
The air used for the combustion of wood comes
from under the grate when the air intake damper is
open. This air also ensures the cooling of the grate.
It is therefore
performances and to avoid damage of the grate
under the the effect of overheating, it is also
necessary to avoid its obstruction in proceeding in
regular ash removal and the clearing of the ashes.
the appliance
necessary to get
- The scraper allows to make the ash removal of
the grate (Fig. 20).
- The ashtray- fixed under the grid - is easily
removable by pulling it out thanks to the cold
hand.
•
The level of the ashes must never reach the cast
iron grate of the appliance.

7.4.4 - Safety regulations

•
Never throw water to put the fire out.
•
The window of the appliance is very hot : be careful
you don't get burnt notably children.
•
The appliance gives out important heat through
radiation : don't put materials nor heat-sensitive
under
objects within a distance inferior of 1,50 m to the
window.
•
Empty the content of the ash pan in a metallic or
inflammable container kept for this use only. The
ashes which look like cold can actually be very hot,
even after some cooling time.
•
Don't place easily inflammable materials in the
environment of the appliance and in the place
where you store wood.
•
Particularly, don't store wood under the appliance
(Fig. 24).
•
In case of a chimney fire, put the air intake damper
in a closed position.
8 - ADVICE ON CHIMNEY-SWEEPING AND
STOVE AND SMOKE FLUE MAINTENANCE
The mecanical sweeping of the smoke flue is
compulsory, it has to be made a few times a year and
one sweeping has to done during the heating period. A
certificate has to be established by the professional.
For sweepings, you'll need to :
•
Remove the deflector :
- Dismantle the deflector
if forward (Fig. 15 and 16).
- Let the back part of the du deflector
and take it out (Fig. 17).
- To put the deflector back: proceed in the reverse
way of the dismantling.
•
Check thoroughly the condition of the appliance
paying
elements : seals and locking components, support
parts (door, frame).
•
Check the condition of the smoke flue and the
connecting pipe : all the connections must show
good mecanical holding and must have kept their
smoke-tight features.
•
Vacuum the inside of the hood to avoid any
accumulation of dust ; clear if necessary the hot air
optimal
convection route..
If you detect any irregularities : have your appliance or
your installation repaired by a professional.
19
by lifting it and drawing
special attention to
go down
smoke-tightness