Tabla de contenido
Publicidad
HKS 28 A.book Seite 18 Dienstag, 26. Februar 2019 10:51 10
Less than half of a full tooth should be visible
below the workpiece (see figure A).
Adjusting the Bevel-Angle (see Figure B)
The bevel angle can be adjusted between 0° and 45°.
– Loosen the locking screw 2.
– Adjust the bevel-angle by tilting the machine toward
the base plate. The angle is indicated on the scale 19.
– Tighten the locking screw 2 again.
Mounting/Adjusting
the Parallel Guide
Before any work on the machine itself, remove
the battery.
Adjusting the Parallel Guide (see Figure C)
– Loosen the locking screw 1 and adjust the parallel
guide 11 to the requested clearance to the saw
blade.
– Tighten the locking screw 1 again.
Replacing/
Adjusting the Saw Blade
Before any work on the machine itself, remove
the battery.
Do not use abrasive wheels as the application
tool.
Only use saw blades the maximum permitted
speed of which is equal or higher than the spec-
ified no-load speed.
Changing the Saw Blade
(see Figures D, E, F)
– Remove the Allen key 22 from the storage.
– Press the spindle lock button 14.
– Loosen the fastening screw 24 with the Allen
key 22. Remove the fastening screw 24 and the
clamping flange 23.
Caution: The fastening screw 24 has a left-hand
thread!
– Pull back the retracting blade guard 12 with the
lever 9.
– Change the saw blade 13. The direction-of-rota-
tion arrow on the saw blade must correspond
with the arrow on the retracting blade guard 12
(see figure F).
– Mount the clamping flange 23 again and tighten
the fastening screw 24.
Adjusting the Blade to the Perpendicular
Position (see figure G)
– Use a square to check that the blade is perpendic-
ular to the base plate.
18
– Should an adjustment be required, adjust the an-
gle via the adjusting screw 25 using the Allen
key 22.
Dust/Chip Extraction
Before any work on the machine itself, remove
the battery.
Dusts from materials such as lead-containing
coatings, some wood types, minerals and metal
can be harmful to one's health. Touching or
breathing-in the dusts can cause allergic reac-
tions and/or lead to respiratory infections of the
user or bystanders.
Certain dusts, such as oak or beech dust, are con-
sidered as carcinogenic, especially in connection
with wood-treatment additives (chromate, wood
preservative). Materials containing asbestos may
only be worked by specialists.
- Provide for good ventilation of the working
place.
- It is recommended to wear a P2 filter-class res-
pirator.
Observe the relevant regulations in your country
for the materials to be worked.
Sawdust Ejection
Clean the sawdust ejector 8 regularly. Use a suitable
tool (e. g. piece of wood, compressed air, etc.) to
clean clogged chip ejector.
Keep fingers out of sawdust ejector 8.
External Dust Extraction
The sawdust ejector 8 fits to the connector with the
Art. No. 0702 400 042. For other diameters, an ex-
traction adapter must be used.
Initial Operation
Inserting the Battery
Slide the charged battery 7 in into the handle until it
can be felt to latch.
Switching On/Off
Switching on: Push the lock-off button 4 down-
ward and hold.
Afterwards,
switch 5.
Switching off: Release the On/Off switch 5.
Do not switch the machine on or off while the
saw blade is in contact with the workpiece or
other materials.
press
the
On/Off
Publicidad
Tabla de contenido
