Wheel Assembly - Campbell Hausfeld WL6000 Serie Instrucciones De Operación

Oilless Compressors
General Safety
5. Wear safety glasses
and use hearing
protection when
operating the pump
or unit.
6. Do not stand on or
use the pump or unit as a handhold.
7. Before each use, inspect compressed
air system and electrical components
for signs of damage, deterioration,
weakness or leakage. Repair or
replace defective items before using.
8. Check all fasteners at frequent
intervals for proper tightness.
WARNING
!
Motors, electrical
equipment and controls
can cause electrical arcs
that will ignite a
flammable gas or vapor.
Never operate or repair in or near a
flammable gas or vapor. Never store
flammable liquids or gases in the
vicinity of the compressor.
CAUTION
!
Compressor parts may
be hot even if the unit
is stopped.
9. Keep fingers away
from a running
compressor; fast moving and hot
parts will cause injury and/or burns.
10. If the equipment should start to
abnormally vibrate, STOP the
engine/motor and check
immediately for the cause.
Vibration is generally a warning of
trouble.
11. To reduce fire hazard, keep
engine/motor exterior free of oil,
solvent, or excessive grease.
Never remove or
WARNING
!
attempt to adjust
safety valve. Keep safety valve free
from paint and other accumulations.
DANGER
!
Never attempt to repair
or modify a tank!
Welding, drilling or any
other modification will
weaken the tank
resulting in damage from rupture or
explosion. Always replace worn or
damaged tanks.
Drain liquid from
NOTICE
tank daily.
12. Tanks rust from moisture build-up,
which weakens the tank. Make sure
to drain tank daily and inspect
periodically for unsafe conditions
such as rust formation and
corrosion.
www.chpower.com
13. Fast moving air will stir up dust and
(Con't)
debris which may be harmful.
Release air slowly when draining
moisture or depressurizing the
compressor system.
SPRAYING PRECAUTIONS
WARNING
!
Do not spray flammable
materials in vicinity of
open flame or near
ignition sources
including the compressor unit.
14. Do not smoke when spraying paint,
insecticides, or other flammable
substances.
15. Use a face mask/
respirator when
spraying and spray in
a well ventilated area
to prevent health and
fire hazards.
16. Do not direct paint or other sprayed
material at the compressor. Locate
compressor as far away from the
spraying area as possible to
minimize overspray accumulation
on the compressor.
17. When spraying or cleaning with
solvents or toxic chemicals, follow
the instructions provided by the
chemical manufacturer.
Foot Assembly
The items marked with an asterisk (*)
were shipped loose with the unit (See
Figure 1).
1. Insert bolt through foot and
bracket. The foot should be on the
lower side of bracket.
2. Tightly secure with the lock nut.
Repeat on opposite side.

Wheel Assembly

The items marked with an asterisk (*)
were shipped loose with the unit (See
Figure 1).
1. Insert shoulder bolt through wheel
hub. The bolt hex head should be
on the opposite side of protruding
hub center.
2. On WL6112 Only: Place washers
onto shoulder bolt so that washers
are between wheel and tank axle
iron.
3. Feed the shoulder bolt through the
hole on the tank axle iron and
tightly secure with the locknut.
Repeat on the opposite side.
Foot*
Figure 1 - Foot and Wheel Assembly
Installation
LOCATION
The tank must sit level or slope slightly
towards the drain cock to allow the
tank to drain properly.
It is extremely important to install the
compressor in a clean, well ventilated
area where the surrounding air
temperature will not be more than
100°F.
A minimum clearance of 4 inches
between the compressor and a wall is
required because objects could obstruct
air flow.
inlet near steam, paint spray, sandblast
areas or any other source of
contamination. This debris will damage
the motor.
ELECTRICAL INSTALLATION
connections should be performed by a
qualified electrician. Installation must
be in accordance with local codes and
national electrical codes.
Never use an extension
cord with this product.
Use additional air hose
instead of an extension
cord to avoid power loss
and permanent motor damage. Use of
an extension cord voids the warranty.
GROUNDING INSTRUCTIONS
1. This product is for use on a nominal
2
Nut*
Bolt* Shoulder
Bolt*
Do not locate the
CAUTION
!
compressor air
All wiring and
WARNING
!
electrical
CAUTION
!
120 volt circuit and has a grounding
plug that looks like the plug
illustrated in Figure 2. Make sure the
product is connected to an outlet
having the same configuration as the
plug. This product must be
grounded. In the event of an
electrical short circuit, grounding
reduces risk of electrical shock by
providing an escape wire for electric
current. This product is equipped
with a cord having a grounding wire
Washer*
Lock
Nut*
Wheel*
STOP!