Skil 4270 Manual Original página 11

Ocultar thumbs Ver también para 4270:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 34
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations diferent
from those intended could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR JIG SAWS
GENERAL
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
• Check the functioning of the tool before each use and, in
case of a defect, have it repaired immediately by a
qualiied person; never open the tool yourself
• Do not work materials containing asbestos (asbestos
is considered carcinogenic)
• This tool should not be used by people under the age of
16 years
• The noise level when working can exceed 85 dB(A); wear
ear protection
• Wear protective goggles when working with materials
which produce chips
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classiied as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• Always disconnect plug from power source before
making any adjustment or changing any accessory
BEFORE USE
• Remove all obstacles on top of as well as underneath the
cutting path before you start cutting
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
DURING USE
• Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord (a cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock)
• Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
• Never use the tool when cord is damaged; have it
replaced by a qualiied person
• In case of electrical or mechanical malfunction,
immediately switch of the tool and disconnect the plug
• Keep hands away from the saw blade while the tool is in
use
ACCESSORIES
• SKIL can assure lawless functioning of the tool only
when original accessories are used
• Do not use a saw blade which is cracked, deformed or dull
OUTDOOR USE
• When used outdoors, connect the tool via a fault current
(FI) circuit breaker with a triggering current of 30 mA
maximum, and only use an extension cord which is
intended for outdoor use and equipped with a
splashproof coupling-socket
AFTER USE
• When you put away the tool, switch of the motor and
ensure that all moving parts have come to a complete
standstill
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut of the cord of this tool,
it must be disposed of safely and not left unattended
USE
• On/of 4
• Switch locking for continuous use 5
• Changing saw blades 6
! insert blade to full depth with teeth facing forward
7
• Sawing at 45° 8
- for best results select "CURVE" (4270) / "all/curve"
(4370) sawing mode
! ensure that footplate rests flat against tool
housing (8a or 8b)
• Selecting sawing mode 9
4270
- "CURVE" for accurate cutting, straight + curved
- "TURBO" for fast cutting, straight cuts only
! always select "CURVE" when sawing splinter-
sensitive material
4370
- 1 setting ("all/curve") for accurate cutting in all
materials, straight + curved
- 4 settings for fast cutting in diferent materials, straight
cuts only
grey = metal
blue = plastic
brown = hard wood
green = soft wood
! always select "all/curve" when sawing splinter-
sensitive material
10

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

4370

Tabla de contenido