Dry Vacuum Cleaning - EWT AquaVac NTS 20 BOXTER INOX Manual Del Usuario

Assembly
Make sure that the connector is not plugged in.
Hold the two clamps, which hold the upper sec-
tion in its position and fold them upwards (B2).
Loosen the clamps and lift the upper section up
and out (B3).
Slide the handle (B1) onto the upper section from
the top. Make sure that the guide of the handle
fastener is inserted on the right side in the handle
holder (B4).
Fasten the handle to the upper section with the
two accompanying screws. Tighten the screws
finger-tight (B5).
Turn the tank over so that the upper section is on
the bottom.
Put the four rollers (13) in the guides on the bot-
tom of the tank (B6).
Check that the rollers have been pushed comple-
tely into the guides.
Fasten the rollers with the four remaining screws.
Tighten the screws finger-tight (B7).
Insert the foam plastic filter (9) that has been
supplied for wet vacuuming.
(see the section called "Wet Vacuuming")
Insert the dust bag (15) that has been supplied for
dry vacuuming.
(see the section called "Dry Vacuuming")
Replace the upper section on the tank (B8).
Align the upper section with the clamps (B9).
Hook the clamps into the upper section and let
them snap into place by pressing the clamps
downwards.
Place the large end of the hose (5) on the front air
intake stub (17) on the tank.
Select a nozzle (6, 8) (B1) or the telescopic tube
(7) (B1) and slide it over the suction tube (5) (B1),
(B11).
After using and cleaning the appliance, store the
accessories by attaching them to the correspon-
ding holders on the vacuum cleaner.
14

Dry Vacuum Cleaning

ATTENTION! It is absolutely necessary
for you to read, understand, and
observe the section entitled "Safety
Instructions and Warnings".
NOTE: Never vacuum up hazardous materials.
If an incorrect dust bag is used, then the
guarantee becomes void.
Make sure that the appliance is not plugged into
the power mains.
Make sure that the foam plastic filter (9) (B1) is
clean and dry and installed over the filter basket
(4) (B1) before inserting the dry filter (19) (B1).
Carefully pull the dry filter over the foam plastic
filter (B14).
Place the fastening ring (20) (B1) over the dry filter
and press it down to the rib of the upper section
(B14).
Check to make sure that the dry filter completely
covers the foam plastic filter. Also check to make
sure that all corners of the try filter are being held
in place by the fastening ring.
Slide the dust bag over the hose connection (B15)
in the tank. Press it until it snaps firmly into place
(B16). In the process, make sure that the dust bag
is not damaged.
Place the upper section on the tank once again
and close the clamps (B8), (B9).
Place the large end of the hose on the front air
intake stub on the tank (B10).
Select the desired nozzle (6, 8) (B1) or the tele-
scopic tube(s) (7) (B1); connect it to the vacuum
hose (5) and connect the end of the hose to the air
intake stub on the appliance.
Make sure that the ON/OFF switch (11) (B1) on the
appliance is in the "Off" position (position "0") be-
fore you plug the power plug into the receptacle.
Plug the power plug into the receptacle.
Switch the motor on (ON/OFF switch in position
"I").
When you have finished vacuuming, switch the
motor off by putting the ON/OFF switch (11) (B1)
into the „OFF" position (position „O").
Unplug the power plug.
Check the dust bag (15) (B1) regularly and change
it when it is 2/3 full. The bag is designed such that
only air, and no dust, can pass through the paper.