Publicidad
Idiomas disponibles
Idiomas disponibles
Before connecting up the appliance to the installation, first
check that it has been adjusted for the type of gas with
which it is to be supplied. Our cooking hobs leave the
Provided that national laws so permit, this cooking hob
may be adapted to function with other types of gas. To do
so, all the following steps should be carried out:
1- R emove the pan supports, the cover and the main body
of the burner.
2- Change the burner tip using the spanner provided by
our technical services department (code 424699) taking
special care to ensure that the burner tip does not fall
Ensure that it is completely tightened in order to guarantee
the seal. Fig. 8.
W ith these burners the air does not have to be adjusted.
B) Changing the tips on the upper large double flame
flame burner.
The glass panel and the frame are fixed to the rest of the
cooking hob by means of clips. The following steps must
be taken to remove both the glass panel and frames:
1 - Remove all the burners, caps, diffusers, etc. Fig. 9a.
2 - Loosen the two screws on the rapid, semi-rapid and
auxiliary burners. Fig. 9b.
3 - Loosen the three screws on the large double flame
burner Fig. 9c.
4 - Use the disassembly lever 483196 available from o
technical assistance service. To release the front clips,
apply the lever in the area shown in figures X1, X2, X3,
depending on the hob model.
Never use the lever on glass edges which have no trim
or frame
!
Before putting the glass back, check that the watertight
seals are properly adjusted.
5 - To release the rear clips, carefully raise the entire glass
unit along with the frame, as in Fig. X4.
6 - Changing the outer flame burner tip.
Take out the main burner tip turning it to the left with a 10 mm
spanner. At the same time, hold the burner tip casing in
the opposite direction with a 13 mm spanner. Fig.
Screw in the new main burner tip, pushing the burner tip
casing in the opposite direction with a 13 mm spanner.
Loosen the holding screw Fig. L1 and set the regulating
bushing of the air flow to the value indicated in the burner
tip table. -Z -
Tighten the locking screw.
7 - Changing the inner flame burner tip.
Using an 8 mm spanner, unscrew the connector Fig. M3
from the threaded component Fig. M2. To do this, hold
the threaded component firmly in the opposite direction
using a 12 mm spanner. See Fig. N.
Then, using a 12 mm spanner, unscrew the threaded
component Fig. M2 from the component Fig. M1, holding
the latter firmly in the opposite direction with a 12 mm
spanner. See Fig. O.
Unscrew the burner tip Fig. M4 from component Fig. M2
and replace it with the appropriate burner tip as indicated
in the burner tip table, and adjust the regulating bushing
of the air flow M5 in line with the value indicated in the
burner tip table. -Y-
*
In this case follow this procedure:
1 - Loosen the fixing clips of the appliance to the kitchen
unit.
2 - Loosen the main gas connection and take the appliance
3 - Apply the disassembly lever 483196 as shown in
Fig. W .
C) Adjusting the reduced consumption of taps and
burners and of the cooking hob
1 - Set the taps to minimum.
2 - Remove the control knobs from the taps. Fig. 10
3 - It has a flexible rubber seal. Simply apply pressure with
the tip of the screwdriver to release the thread toward
the tap's adjusting screw. Fig. 11.
Do not remove the disc seal.
4 - Adjust the By-pass screw.
Depending on the type of gas you wish to change the
appliance to, you must perform one of the following
processes, marked A, B, C and D:
A) The By-pass screws must be fully done up.
B) The By-pass screws must be loosened until the
correct flame is achieved.
C) The By-pass screws that are fitted on the appliance
must be substituted for the ones that are supplied in the
transformation kit.
D) In this case, you must not alter the By-pass screws.
In all cases, after the gas changeover has been carried
out, make sure that the burner flames are correct by
ensuring that when you go from the maximum setting to
the minimum they do not go out and there is no flame
backdraught.
Consult Table III in order to find out which case applies
to you: A, B, C or D.
5 - It is important that all the reinforcement rings are in
place in order to ensure that the electrics are sealed to
protect against any liquids that may spill from the hob.
6 - Replace the control knobs on the taps.
ur
Do not dismantle the tap shaft
malfunction, change the whole tap.
D) Place the sticker indicating that the appliance's gas
supply has been changed next to the specifications
K.
, Fig. 12: In the event of a
plate.
Publicidad
